Network Working Group J. Chroboczek Internet-Draft IRIF, University of Paris-Diderot Intended status: Informational April 6, 2018 Expires: October 8, 2018 Applicability of the Babel routing protocol draft-ietf-babel-applicability-02 Abstract Where we argue that although OSPF and IS-IS are fine protocols, there exists a space where the Babel routing protocol (RFC 6126bis) can be useful. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on October 8, 2018. Copyright Notice Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Chroboczek Expires October 8, 2018 [Page 1] Internet-Draft Babel Protocol Applicability April 2018 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. Technical overview of the Babel protocol . . . . . . . . 2 1.2. Properties of the Babel protocol . . . . . . . . . . . . 3 1.3. Limitations . . . . . . . . . . . . . . . . . . . . . . . 5 2. Existing successful deployments of Babel . . . . . . . . . . 6 2.1. Hybrid networks . . . . . . . . . . . . . . . . . . . . . 6 2.2. Large scale overlay networks . . . . . . . . . . . . . . 6 2.3. Pure mesh networks . . . . . . . . . . . . . . . . . . . 6 2.4. Small unmanaged networks . . . . . . . . . . . . . . . . 7 3. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7 4. Security Considerations . . . . . . . . . . . . . . . . . . . 7 5. Informational References . . . . . . . . . . . . . . . . . . 7 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 9 1. Introduction Babel [RFC6126bis] is a routing protocol based on the familiar distance-vector algorithm (sometimes known as distributed Bellman- Ford) augmented with mechanisms for loop avoidance (there is no "counting to infinity") and starvation avoidance. In this document, we argue that there exist niches where Babel is useful and that are not adequately served by the mature, efficient and highly refined protocols that are usually deployed, such as OSPF [RFC5340] and IS-IS [RFC1195]. 1.1. Technical overview of the Babel protocol At its core, Babel is a traditional distance-vector protocol based on the distributed Bellman-Ford algorithm, similar in principle to RIP [RFC2453], but with two obvious extensions: provisions for explicit neighbour reachability, bidirectional reachability and link-quality sensing, and support for multiple address families (e.g., IPv6 and IPv4) in a single protocol instance. Algorithms of this class are simple to understand and simple to implement, but unfortunately they do not work very well -- they suffer from "counting to infinity", a case of pathologically slow convergence in some topologies after a link has been brought down. Babel uses a mechanism pioneered by EIGRP [DUAL] [RFC7868], known as "feasibility", which avoids routing loops and therefore makes counting to infinity impossible. Feasibility is a very conservative mechanism, one that not only rejects all looping routes, but also rejects some loop-free routes; it can easily lead to a situation known as starvation, where a router rejects all routes to a given destination, even those that are loop- Chroboczek Expires October 8, 2018 [Page 2] Internet-Draft Babel Protocol Applicability April 2018 free. In order to recover from starvation, Babel uses a mechanism pioneered by DSDV [DSDV] and known as "sequenced routes". In Babel, this mechanism is generalised to deal with prefixes of arbitrary length and routes announced at multiple points in a single routing domain (DSDV was a pure mesh protocol, and did not need to deal with such details). The sequenced routes algorithm is slow to react to a starvation episode. In Babel, starvation recovery is accelerated by using explicit requests (known as "seqno requests" in the protocol) to signal a starvation episode and to cause a new sequenced route to be propagated in the network. In the absence of packet loss, this mechanism is provably complete and clears the starvation in time proportional to the diameter of the network, at the cost of some additional signalling traffic. 1.2. Properties of the Babel protocol The fairly strong properties of the Babel protocol (convergence, loop avoidance, starvation avoidance) rely on some rather weak properties of the network and the metric being used. The most significant are: o causality: a control message is not received before it has been sent; o strict monotonicity of the metric: M < C + M; o left-distributivity of the metric: if M <= M', then C + M <= C + M'. In particular, Babel does not assume a reliable transport, it does not require an ordered transport, it does not require transitive communication, and it does not require that the metric be discrete (continuous metrics are possible, reflecting for example packet loss rates). This is in contrast to traditional link-state routing protocols such as OSPF [RFC5340] or IS-IS [RFC1195] which are layered over a reliable flooding algorithm and make some rather strong requirements on the underlying network and metric. 1.2.1. Simplicity and implementability Babel is a conceptually simple protocol. It consists of a familiar algorithm (distributed Bellman-Ford) augmented with three simple and well-defined mechanisms (feasibility, sequenced routes and explicit requests). Given a sufficiently friendly audience, the principles behind Babel can be explained in 15 minutes, and a full description of the protocol can be done in 52 minutes (one microcentury). Chroboczek Expires October 8, 2018 [Page 3] Internet-Draft Babel Protocol Applicability April 2018 An important consequence is that Babel is easy to implement. While Babel is a young protocol, there already exist four independent implementations, one of which was reportedly written and debugged in just two nights. 1.2.2. Robustness Babel's correctness depends on a small number of fairly weak and reasonably obvious properties. This makes Babel in many ways a robust protocol: o robust with respect to bugs: unless you are very unlucky, an implementation bug does probably not violate the properties on which Babel relies; in practice, implementation bugs tend to slow down convergence or cause sub-optimal routing, but do not cause the protocol to collapse; o robust with respect to broken networks: a fragile network (non- transitive links, unstable links, etc.) does most probably not violate the assumptions of the protocol; o robust with respect to strange metrics: no matter how strange your metric (continuous, constantly fluctuating, etc.), it does most probably not violate the assumptions of the protocol. These robustness properties have important consequences for the applicability of the protocol: Babel works (more or less efficiently) in a wide range of networks where traditional routing protocols give up. 1.2.3. Extensibility Babel's packet format has a number of features designed to make the protocol extensible, and a number of extensions have been designed to make Babel work in situations that were not envisioned when the protocol was initially designed. This extensibility is not an accident, but a consequence of the design of the protocol: it is easy to check whether a given extension violates the assumptions made by the protocol. Remarkably enough, all of the extensions designed to date interoperate with the base protocol and with each other. Again, this is a consequence of the protocol design: in order to check the interoperability of two implementations of Babel, it is enough to verify that the interaction of the two does not violate the protocol's assumptions. Notable extensions deployed to date include: Chroboczek Expires October 8, 2018 [Page 4] Internet-Draft Babel Protocol Applicability April 2018 o source-specific routing (SADR) [BABEL-SS], which allows routing to take a packet's source address into account, thus enabling a cheap form of multihoming; o RTT-based routing [BABEL-RTT], which allows routing to minimise link delay, which is useful in overlay network (where both hop count and packet loss are poor metrics). Some other extensions have been designed, but have not seen deployment yet (and their usefulness is yet to be demonstrated): o frequency-aware routing [BABEL-Z], which allows routing to minimise radio interference in wireless networks; o ToS-aware routing [BABEL-TOS], which allows routing to take a packet's ToS marking into account for selected routes without incurring the full cost of a multi-topology routing protocol. 1.3. Limitations Babel has some undesirable properties that make it suboptimal or even unusable in some deployments. 1.3.1. Periodic updates The main mechanisms used by Babel to reconverge after a topology change are reactive: triggered updates, triggered retractions and explicit requests. However, in the presence of heavy packet loss, Babel relies on periodic updates to clear routing pathologies. This reliance on periodic updates makes Babel unsuitable in at least two kinds of deployments: o large, stable networks: since Babel sends periodic updates even in the absence of topology changes, in well-managed large, stable networks, protocols that rely on a reliable transport (such as OSPF, IS-IS or EIGRP) are intrinsically more efficient; o low-power networks: the periodic updates use up battery power even when there are no topology changes, which makes Babel undesirable in stable, low-power networks. 1.3.2. Full routing table While there exist techniques that allow a Babel speaker to function with a partial routing table (e.g., by using just a default route), the basic design of the protocol is that every Babel speaker has a full routing table. In networks where some nodes are too constrained Chroboczek Expires October 8, 2018 [Page 5] Internet-Draft Babel Protocol Applicability April 2018 to hold a full routing table, protocols such as AODVv2 [AODVv2], RPL [RFC6550] and LOADng [LOADng] may be preferable to Babel. 1.3.3. Slow aggregation Babel's loop-avoidance mechanism relies on making a route unreachable after a retraction until all neighbours have been guaranteed to have acted upon the retraction, even in the presence of packet loss. Unless the optional algorithm described in Section 3.5.5 of [RFC6126bis] is implemented, this entails that a node is unreachable for a few minutes after the most specific route to it has been retracted. This property may make Babel undesirable in networks that perform automatic aggregation. 2. Existing successful deployments of Babel In this section, we give a few examples of environments where Babel has been successfully deployed. 2.1. Hybrid networks Babel is able to deal with both classical, prefix-based ("Internet- style") routing and flat ("mesh-style") routing over non-transitive link technologies. Because of that, it has seen a number of succesful deployments in medium-sized hybrid networks, networks that combine a wired, aggregated backbone with meshy wireless bits at the edges. No other routing protocol known to us is similarly robust and efficient in this particular type of network. 2.2. Large scale overlay networks The algorithms used by Babel (loop avoidance, hysteresis, delayed updates) allow it to remain stable and efficient in the presence of unstable metrics, even in the presence of a feedback loop. For this reason, it has been successfully deployed in large scale overlay networks, built out of thousands of tunnels spanning continents, where it is used with a metric computed from links' latencies [DELAY-BASED]. This particular application depends on the extension for RTT- sensitive routing. 2.3. Pure mesh networks While Babel is a general-purpose routing protocol, it has been repeatedly shown to be competitive with dedicated routing protocols for wireless mesh networks [REAL-WORLD] [BRIDGING-LAYERS]. While this particular niche is already served by a number of mature Chroboczek Expires October 8, 2018 [Page 6] Internet-Draft Babel Protocol Applicability April 2018 protocols, notably OLSR-ETX and OLSRv2 [RFC7181] equipped with the DAT metric [RFC7779], Babel has seen a moderate amount of successful deployment in pure mesh networks. 2.4. Small unmanaged networks Because of its small size and simple configuration, Babel has been deployed in small, unmanaged networks (three to five routers), where it serves as a more efficient replacement for RIP [RFC2453], over which it has two significant advantages: the ability to route multiple address families (IPv6 and IPv4) in a single protocol instance, and good support for using wireless links for transit. 3. IANA Considerations This document requires no IANA actions. [RFC Editor: please remove this section before publication.] 4. Security Considerations As in all distance-vector routing protocols, a Babel speaker receives reachability information from its neighbours, which by default is trusted. A number of attacks are possible if this information is not suitably protected, either by a lower-layer mechanism or by an extension to the protocol itself (e.g. [RFC7298]). Implementors and deployers must be aware of the insecure nature of the base protocol, and must take suitable measures to ensure that the protocol is deployed as securely as required by the application. 5. Informational References [AODVv2] Perkins, C., Ratliff, S., Dowdell, J., Steenbrink, L., and V. Mercieca, "Ad Hoc On-demand Distance Vector Version 2 (AODVv2) Routing", draft-ietf-manet-aodvv2-16 (work in progress), May 2016. [BABEL-RTT] Jonglez, B. and J. Chroboczek, "Delay-based Metric Extension for the Babel Routing Protocol", draft-jonglez- babel-rtt-extension-01 (work in progress), May 2015. [BABEL-SS] Boutier, M. and J. Chroboczek, "Source-Specific Routing in Babel", draft-ietf-babel-source-specific-03 (work in progress), August 2018. Chroboczek Expires October 8, 2018 [Page 7] Internet-Draft Babel Protocol Applicability April 2018 [BABEL-TOS] Chouasne, G. and J. Chroboczek, "TOS-Specific Routing in Babel", draft-chouasne-babel-tos-specific-00 (work in progress), July 2017. [BABEL-Z] Chroboczek, J., "Diversity Routing for the Babel Routing Protocol", draft-chroboczek-babel-diversity-routing-01 (work in progress), February 2016. [BRIDGING-LAYERS] Murray, D., Dixon, M., and T. Koziniec, "An Experimental Comparison of Routing Protocols in Multi Hop Ad Hoc Networks", Proc. ATNAC 2010, 2010. [DELAY-BASED] Jonglez, B. and J. Chroboczek, "A delay-based routing metric", March 2014, . [DSDV] Perkins, C. and P. Bhagwat, "Highly Dynamic Destination- Sequenced Distance-Vector Routing (DSDV) for Mobile Computers", ACM SIGCOMM'94 Conference on Communications Architectures, Protocols and Applications 234-244, 1994. [DUAL] Garcia Luna Aceves, J., "Loop-Free Routing Using Diffusing Computations", IEEE/ACM Transactions on Networking 1:1, February 1993. [LOADng] Clausen, T., Verdiere, A., Yi, J., Niktash, A., Igarashi, Y., Satoh, H., Herberg, U., Lavenu, C., Lys, T., and J. Dean, "The Lightweight On-demand Ad hoc Distance-vector Routing Protocol - Next Generation (LOADng)", draft- clausen-lln-loadng-15 (work in progress), January 2017. [REAL-WORLD] Abolhasan, M., Hagelstein, B., and J. Wang, "Real-world performance of current proactive multi-hop mesh protocols", Asia-Pacific Conference on Communication 2009, 2009. [RFC1195] Callon, R., "Use of OSI IS-IS for routing in TCP/IP and dual environments", RFC 1195, December 1990. [RFC2453] Malkin, G., "RIP Version 2", STD 56, RFC 2453, November 1998. [RFC5340] Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF for IPv6", RFC 5340, July 2008. Chroboczek Expires October 8, 2018 [Page 8] Internet-Draft Babel Protocol Applicability April 2018 [RFC6126bis] Chroboczek, J. and D. Schinazi, "The Babel Routing Protocol", Internet Draft draft-ietf-babel-rfc6126bis-04, October 2017. [RFC6550] Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J., Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur, JP., and R. Alexander, "RPL: IPv6 Routing Protocol for Low-Power and Lossy Networks", RFC 6550, March 2012. [RFC7181] Clausen, T., Dearlove, C., Jacquet, P., and U. Herberg, "The Optimized Link State Routing Protocol Version 2", RFC 7181, April 2014. [RFC7298] Ovsienko, D., "Babel Hashed Message Authentication Code (HMAC) Cryptographic Authentication", RFC 7298, DOI 10.17487/RFC7298, July 2014, . [RFC7779] Rogge, H. and E. Baccelli, "Directional Airtime Metric Based on Packet Sequence Numbers for Optimized Link State Routing Version 2 (OLSRv2)", RFC 7779, DOI 10.17487/RFC7779, April 2016. [RFC7868] Savage, D., Ng, J., Moore, S., Slice, D., Paluch, P., and R. White, "Cisco's Enhanced Interior Gateway Routing Protocol (EIGRP)", RFC 7868, DOI 10.17487/RFC7868, May 2016. Author's Address Juliusz Chroboczek IRIF, University of Paris-Diderot Case 7014 75205 Paris Cedex 13 France Email: jch@irif.fr Chroboczek Expires October 8, 2018 [Page 9]