6LoWPAN Working Group E. Kim Internet-Draft ETRI Expires: January 29, 2011 D. Kaspar Simula Research Laboratory N. Chevrollier TNO JP. Vasseur Cisco Systems, Inc July 28, 2010 Design and Application Spaces for 6LoWPANs draft-ietf-6lowpan-usecases-06 Abstract This document investigates potential application scenarios and use cases for low-power wireless personal area networks (LoWPANs). This document provides dimensions of design space for LoWPAN applications. A list of use cases and market domains that may benefit and motivate the work currently done in the 6LoWPAN WG is provided with the characterisitcis of each dimention. A complete list of practical use cases is not the goal of this document. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on January 29, 2011. Copyright Notice Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents Kim, et al. Expires January 29, 2011 [Page 1] Internet-Draft 6LoWPAN Design and Applications July 2010 (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 4 1.2. Basic Network Configuration . . . . . . . . . . . . . . . 5 2. Design Space . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. Application Scenarios . . . . . . . . . . . . . . . . . . . . 8 3.1. Industrial Monitoring . . . . . . . . . . . . . . . . . . 8 3.1.1. A Use Case and its Requirements . . . . . . . . . . . 9 3.1.2. 6LoWPAN Applicability . . . . . . . . . . . . . . . . 10 3.2. Structural Monitoring . . . . . . . . . . . . . . . . . . 12 3.2.1. A Use Case and its Requirements . . . . . . . . . . . 12 3.2.2. 6LoWPAN Applicability . . . . . . . . . . . . . . . . 13 3.3. Connected Home . . . . . . . . . . . . . . . . . . . . . . 14 3.3.1. A Use Case and its Requirements . . . . . . . . . . . 15 3.3.2. 6LoWPAN Applicability . . . . . . . . . . . . . . . . 16 3.4. Healthcare . . . . . . . . . . . . . . . . . . . . . . . . 18 3.4.1. A Use Case and its Requirements . . . . . . . . . . . 18 3.4.2. 6LoWPAN Applicability . . . . . . . . . . . . . . . . 19 3.5. Vehicle Telematics . . . . . . . . . . . . . . . . . . . . 20 3.5.1. A Use Case and its Requirements . . . . . . . . . . . 20 3.5.2. 6LoWPAN Applicability . . . . . . . . . . . . . . . . 21 3.6. Agricultural Monitoring . . . . . . . . . . . . . . . . . 22 3.6.1. A Use Case and its Requirements . . . . . . . . . . . 22 3.6.2. 6LoWPAN Applicability . . . . . . . . . . . . . . . . 24 4. Security Considerations . . . . . . . . . . . . . . . . . . . 26 5. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 27 6. References . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6.1. Normative References . . . . . . . . . . . . . . . . . . . 28 6.2. Informative References . . . . . . . . . . . . . . . . . . 28 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 29 Kim, et al. Expires January 29, 2011 [Page 2] Internet-Draft 6LoWPAN Design and Applications July 2010 1. Introduction Low-power and lossy networks (LLNs) is the term commonly used to refer to networks made of highly constrained nodes (limited CPU, memory, power) interconnected by a variety of "lossy" links (low- power radio links or powerline communication (PLC)). They are characterized by low speed, low performance, low cost, and unstable connectivity. A LoWPAN is a particular instance of an LLN, formed by devices complying with the IEEE 802.15.4 standard [5]. Their typical characteristics can be summarized as follows: o Limited processing capability: the smallest common LoWPAN nodes have 8-bit processors with clock rates around 10 MHz. Other models exist with 16-bit and 32-bit cores (typically ARM7), running at frequencies in the order of tens of MHz. o Small memory capacity: common RAM sizes for LoWPAN devices consist of a few kilobytes, usually 4K or 8K bytes. However, a wide variety of RAM sizes is available, reaching from 1K up to 256K bytes. o Low power: wireless radios for LoWPANs are normally battery- operated. Their RF transceivers often have a current draw of about 10 to 30 mA, depending on the used transmission power level. In order to reach common indoor ranges of up to 30 meters and outdoor ranges of 100 meters, the used transmission power is set around 0 to 3 dBm. Depending on the processor type, there is an additional battery current consumption of the CPU itself, commonly in the order of tens of milliamperes. However, the CPU power consumption can often be reduced by a thousandfold when switching to sleep mode. o Short range: the Personal Operating Space (POS) defined by IEEE 802.15.4 implies a range of 10 meters. For real implementations, the range of LoWPAN radios is typically measured in tens of meters, but can reach over 100 meters in line-of-sight situations. o Low bit rate: the IEEE 802.15.4 standard defines a maximum over- the-air rate of 250K bit/s, which is most commonly used in current deployments. Alternatively, three lower data rates of 20K, 40K and 100K bit/s are defined. As any other LLN, a LoWPAN does not necessarily comprise of sensor nodes only, but may also consist of actuators. For instance, in an agricultural environment, sensor nodes might be used to detect low soil humidity and then send commands to activate the sprinkler system. Kim, et al. Expires January 29, 2011 [Page 3] Internet-Draft 6LoWPAN Design and Applications July 2010 After defining common terminology in Section 1.1 and describing the characteristics of LoWPANs in Section 2, this document provides a list of use cases and market domains that may benefit and motivate the work currently done in the 6LoWPAN WG. 1.1. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [1]. Readers are expected to be familiar with all the terms and concepts that are discussed in "IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals" [3], and " Transmission of IPv6 Packets over IEEE 802.15.4 Networks" [4]. Readers would benefit from reading 6LoWPAN ND [6], 6LoWPAN header compression [7], and 6LoWPAN Routing Requirements [8] for the details of the each 6LoWPAN work. This specification makes extensive use of the same terminology defined in 6LoWPAN ND [6] unless otherwise redefined below. This document defines additional terms: LN (LoWPAN Node) Any host or router participating in a LoWPAN. This term is used when referring to situations in which either a host or router can play the role described. LR(LoWPAN Router) An intermediate router in the LoWPAN who can communicate with other LoWPAN routers in the same LoWPAN. LoWPAN routers are present only in Route Over topologies. LM (LoWPAN Mesh Node) A LoWPAN node that forwards data between arbitary source- destination pairs using link-layer addresses and thus only exists in Mesh Under topologies. LC(local-controller) Kim, et al. Expires January 29, 2011 [Page 4] Internet-Draft 6LoWPAN Design and Applications July 2010 A logical functional entity that performs the special role of coordinating and controlling its child nodes for local data aggregation, status management of local nodes, etc. Thus, the local controller nodes may be multiple instance in a LoWPAN. LBR (LoWPAN Border Router) A border router located at the junction of separate LoWPAN networks or between a LoWPAN network and another IP network. There may be one or more LBRs at the LoWPAN network boundary. A LBR is the responsible authority for IPv6 Prefix propagation for the LoWPAN network it is serving. An isolated LoWPAN also contains a LBR in the network, which provides the prefix(es) for the isolated network. 1.2. Basic Network Configuration The IEEE 802.15.4 standard distinguishes between two types of nodes, reduced-function devices (RFDs) and full-function devices (FFDs). As this distinction is based on some MAC features that are not always in use, we are not using this distinction in this document. Kim, et al. Expires January 29, 2011 [Page 5] Internet-Draft 6LoWPAN Design and Applications July 2010 2. Design Space Inspired by [9], this section lists the dimensions used to describe the design space of wireless sensor networks in the context of the 6LoWPAN Working Group. The design space is already limited by the unique characteristics of a LoWPAN (e.g., low-power, short range, low-bit rate) as described in [3]. The possible dimensions for scenario categorization used in this document are described as follows: o Deployment: LoWPAN nodes can be scattered randomly or they may be deployed in an organized manner in a LoWPAN. The deployment can occur at once, or as an iterative process. The selected type of deployment has an impact on node density and location. This feature affects how to organize (manually or automatically) the LoWPAN and how to allocate addresses in the network. o Network Size: The network size takes into account nodes that provide the intended network capability. The number of nodes involved in a LoWPAN could be small (10 nodes), moderate (several 100s), or large (over a 1000). o Power Source: The power source of nodes, whether the nodes are battery-powered or mains-powered, influences the network design. The power may also be harvested from solar cells or other sources of energy. Hybrid solutions are possible where only part of the network is mains-powered. o Connectivity: Nodes within a LoWPAN are considered "always connected" when there is a network connection between any two given nodes. However, due to external factors (e.g., extreme environment, mobility) or programmed disconnections (e.g., sleeping mode), the network connectivity can be from "intermittent" (i.e., regular disconnections) to "sporadic" (i.e., almost always disconnected network). Differences in L2 duty- cycling settings may additionally impact the connectivity due to highly varying bit-rates. o Multi-hop communication: The multi-hop communication factor highlights the number of hops that has to be traversed to reach the edge of the network or a destination node within it. A single hop may be sufficient for simple star-topologies, but a multi-hop communication scheme is required for more elaborate topologies, such as meshes or trees. In previous work by academia and industry on LoWPANs, various routing mechanisms were introduced, such as data-centric, event-driven, address-centric, localization- based, geographical routing, etc. This document does not make use of such a fine granularity but rather uses topologies and single/ Kim, et al. Expires January 29, 2011 [Page 6] Internet-Draft 6LoWPAN Design and Applications July 2010 multi-hop communication. o Traffic Pattern: several traffic patterns may be used in LoWPANs. To name a few, Point-to-Multi-Point (P2MP), Multi-Point-to-Point (MP2P) and Point-to-Point (P2P). o Security Level: LoWPANs may carry sensitive information and require high-level security support where the availability, integrity, and confidentiality of the information are crucial. This high level of security may be needed in case of structural monitoring of key infrastructure or health monitoring of patients. o Mobility: Inherent to the wireless characteristics of LoWPANs, nodes could move or be moved around. Mobility can be an induced factor (e.g., sensors in an automobile), hence not predictable, or a controlled characteristic (e.g., pre-planned movement in a supply chain). o Quality of Service (QoS): for mission-critical applications, support of QoS is mandatory in resource-constrained LoWPANs. Kim, et al. Expires January 29, 2011 [Page 7] Internet-Draft 6LoWPAN Design and Applications July 2010 3. Application Scenarios This section lists a fundamental set of LoWPAN application scenarios in terms of system design. A complete list of practical use cases is not the objective of this document. 3.1. Industrial Monitoring LoWPAN applications for industrial monitoring can be associated with a broad range of methods to increase productivity, energy efficiency, and safety of industrial operations in engineering facilities and manufacturing plants. Many companies currently use time-consuming and expensive manual monitoring to predict failures and to schedule maintenance or replacements in order to avoid costly manufacturing downtime. LoWPANs can be inexpensively installed to provide more frequent and more reliable data. The deployment of LoWPANs can reduce equipment downtime and eliminate manual equipment monitoring that is costly to be carried out. Additionally, data analysis functionality can be placed into the network, eliminating the need for manual data transfer and analysis. Industrial monitoring can be largely split into the following application fields: o Process Monitoring and Control: combining advanced energy metering and sub-metering technologies with wireless sensor networking in order to optimize factory operations, reduce peak demand, ultimately lower costs for energy, avoid machine downtimes, and increase operation safety. A plant's monitoring boundary often does not cover the entire facility but only those areas considered critical to the process. Easy to install wireless connectivity extends this line to include peripheral areas and process measurements that were previously infeasible or impractical to reach with wired connections. o Machine Surveillance: ensuring product quality and efficient and safe equipment operation. Critical equipment parameters such as vibration, temperature, and electrical signature are analyzed for abnormalities that are suggestive of impending equipment failure (see Section 3.2). o Supply Chain Management and Asset Tracking: with the retail industry being legally responsible for the quality of sold goods, early detection of inadequate storage conditions with respect to temperature will reduce risk and cost to remove products from the sales channel. Examples include container shipping, product identification, cargo monitoring, distribution and logistics. Kim, et al. Expires January 29, 2011 [Page 8] Internet-Draft 6LoWPAN Design and Applications July 2010 o Storage Monitoring: sensor systems designed to prevent releases of regulated substances to ground water, surface water and soil. This application field may also include theft/tampering prevention systems for storage facilities or other infrastructure, such as pipelines. 3.1.1. A Use Case and its Requirements Example: Hospital Storage Rooms In a hospital, maintenance of the right temperature in storage rooms is very critical. Red blood cells need to be stored at 2 to 6 degrees Celsius, blood platelets at 20 to 24 C, and blood plasma below -18 C. For anti-cancer medicine, maintaining a humidity of 45% to 55% is required. Storage rooms have temperature sensors and humidity sensors every 25m to 100m, based on the floor plan and the location of shelves, as indoor obstacles distort the radio signals. At each blood pack a sensor tag can be installed to track the temperature during delivery. A LoWPAN node is installed in each container of a set of blood packs. In this case, highly dense networks must be managed. All nodes are statically deployed and manually configured with either a single- or multi-hop connection. Different types of LoWPAN nodes are configured based on the service and network requirements. All LoWPAN nodes do not move unless the blood packs or a container of blood packs is moved. Moving nodes get connected by logical attachment to a new LoWPAN. When containers of blood packs are transferred to another place of the hospital or by ambulance, the LoWPAN nodes on the containers associate to a new LoWPAN. This type of application works based on both periodic and event- driven notifications. Periodic data is used for monitoring the temperature and humidity in the storage rooms. The data over or under a pre-defined threshold is meaningful to report. Blood cannot be used if it is exposed to the wrong environment for about 30 minutes. Thus, event-driven data sensed on abnormal occurrences is time-critical and requires secure and reliable transmission. LoWPANs must be provided with low installation and management costs, and for the transportation of boold containers, precise location tracking of containers is important. The hospital network manager or staff can be provided with an early warning of possible chain ruptures, for example by conveniently accessing comprehensive online reports and data management systems. Dominant parameters in industrial monitoring scenarios: Kim, et al. Expires January 29, 2011 [Page 9] Internet-Draft 6LoWPAN Design and Applications July 2010 o Deployment: pre-planned, manually attached o Mobility: no (except for asset tracking) o Network Size: medium to large size, high node density o Power Source: most of the time battery-operated o Security Level: business-critical. Secure and reliable transmission must be guaranteed. o Multi-hop communication: multi-hop networking o Connectivity: always on for crucial processes o QoS: important for time-critical event-driven data o Traffic Pattern: P2P (actuator control), MP2P (data collection) o Other Issues: Sensor network management, location tracking, real- time early warning 3.1.2. 6LoWPAN Applicability The network configuration of the above use case can differ substantially by system design. As illustrated in Figure 1, the simplest way is to build a star topology inside of each storage room, and connect the storage rooms with one link but overall network configuration is with mesh topologies. Each LoWPAN node reaches the LBR by a pre-defined routing/forwarding mechanism. LCs play a role in aggregation of the sensed data. In case that the sensed data from an individual node is important, such as urgent event-driven data, it will not be accumulated (and further delayed) by the LoWPAN LCs but immediately relayed. In Route Over topologies, IP forwarding is used, while link-layer addresses in the mesh-header defined by RFC 4944 [4] are used for transmission in Mesh Under topologies . Each LoWPAN node configures its link-local address and get a prefix from its LBR by an 6LoWPAN ND procedure [6]. Based on the layout and size of the storage room, the LoWPAN can be configured in a different way of mesh topology as shown in Figure 2. More than one LoWPAN LCs can be installed in a storage room, and LCs collect data as relay points to transmit the sensed data toward the LBRs. LoWPAN nodes need to build a multi-hop connection to reach the LCs and LBR by either Mesh Under or Route Over. In Mesh Under, more than one LMs are selected for multi-hop transmission and the nodes MAY also play role in transmission multi-point traffic (multicast) by unicast method, not only role in data collection. In Route Over, LRs will Kim, et al. Expires January 29, 2011 [Page 10] Internet-Draft 6LoWPAN Design and Applications July 2010 handle multicast traffic to their LoWPAN links. The data volume is usually not so big in this case, but data is sensitive for delay. Data aggregators can be installed for each storage room, or just one data aggregator can collect all data. To make a light transmission, UDP is likely to be chosen, but secure transmission and security mechanism MUST be added. To increase security, link-layer mechanisms and/or additional security mechanisms SHOULD be used. Because a failure of a LoWPAN node can critically affect the storage of the blood packs, network management is important in this use-case. A light weight management mechanism MUST be provided for the management. When a container is moved out from the storage room, and connected to the other hospital system (if the hospital buildings are fully or partly covered with LoWPANs), a mechanism to rebind to a new parent node and a new LoWPAN MUST be supported. In case that it is moved by an ambulance, it will be connected to an LBR in the vehicle. This typle of mobility is supported by 6LoWPAN ND and routing mechanism. LoWPANs MUST be provided with low installation and management costs, providing benefits such as reduced inventory, and precise location tracking of containers, and mobile equipment (moving beds at the hospital or ambulances). LBR | LBR: LoWPAN Border Router LC----------LC----------LC LC: Local Controller node / | \ / | \ / | \ (Data Aggregator) n n n n n n n n n n: LoWPAN node Figure 1: Storage rooms with a simple star topology Kim, et al. Expires January 29, 2011 [Page 11] Internet-Draft 6LoWPAN Design and Applications July 2010 +------------+-----------+ | | | LBR: LoWPAN Border Router LBR LBR LBR(LC) LC: Local Controller node | | | (Data Aggregator) LC - n LC - n n n: LoWPAN Node / | | | | / \ n n - LC n - n - n n - n | | \ | |\ n n n - n n n n Figure 2: Storage rooms with a mesh topology 3.2. Structural Monitoring Intelligent monitoring in facility management can make safety checks and periodic monitoring of the architecture status highly efficient. Mains-powered nodes can be included in the design phase of a construction or battery-equipped nodes can be added afterwards. All nodes are static and manually deployed. Some data is not critical for security protection (such as normal room temperature), but event- driven emergency data (such as fire alarm) MUST be handled in very critical manner. 3.2.1. A Use Case and its Requirements Example: Bridge Safety Monitoring A 1000m long concrete bridge with 10 pillars is described. Each pillar and the bridge body contain 5 sensors to measure the water level, and 5 vibration sensors are used to monitor its structural health. The LoWPAN nodes are deployed to have 100m line-of-sight distance from each other. All nodes are placed statically and manually configured with a single-hop connection to the local coordinator. All LoWPAN nodes do not move while the service is provided. Except from the pillars, there are no special obstacles of attenuation to the node signals, but careful configuration is needed to prevent signal interference between LoWPAN nodes. The physical network topology is changed in case of node failure. On the top part of each pillar, an sink node is placed to collect the sensed data. The sink nodes of each pillar become data gathering point of the LoWPAN hosts at the pillar as local coordinators. This use case can be extended to medium or large size sensor networks to monitor a building or for instance the safety status of highways and tunnels. Larger networks of the same kind still have similar characteristics such as static node placement, manual deployment and dependent on the blue print of the structure, mesh topologies will be Kim, et al. Expires January 29, 2011 [Page 12] Internet-Draft 6LoWPAN Design and Applications July 2010 built with mains-powered relay points. Periodic and event-driven real-time data gathering is performed and the emergency event-driven data MUST be delivered without delay. Dominant parameters in structural monitoring applications: o Deployment: static, organized, pre-planned o Mobility: none o Network Size: small (dozens of nodes) to large o Power Source: mains-powered nodes are mixed with battery powered (mains-power nodes will be used for local coordination or relays). o Security Level: safety-critical. Secure transmission must be guaranteed. Only authenticated users must be able to access and handle the data. o Multi-hop communication: multi-hop mesh networking is recommended to be supported. o Connectivity: always connected or intermittent by sleeping mode scheduling. o QoS: Emergency notification (fire, over-threshold vibrations, water level, etc.) is required to have priority of delivery and must be transmitted in a highly reliable manner. o Traffic Pattern: MP2P (data collection), P2P (localized querying) o Other Issues: accurate sensing and reliable transmission are important. In addition, sensor status reports should be maintained in a reliable monitoring system. 3.2.2. 6LoWPAN Applicability The network configuration of this use case can be done by simple topologies, but there are many extended use cases for more complex structures. The example bridge monitoring case may be the simplest case. The LoWPAN Nodes are installed on the place after manual optimization of their location. Static data paths to the data gathering points can be set in the commissioning phase. Address configuration and LoWPAN formation are acheived by 6LoWPAN HC [7] and 6LoWPAN ND [6]. Each pillar network may be built as a stub network, so that 16-bit addresses can be utilized (see Section 3 in [7]). Globally routable Kim, et al. Expires January 29, 2011 [Page 13] Internet-Draft 6LoWPAN Design and Applications July 2010 addresses must be allocated to communicate with other LoWPAN nodes. If the network does not use a Route Over mechanism, the 6LoWPAN mesh- header described in RFC 4944 [4] may be used for static data forwarding, unless other mesh under mechanisms are provided. Each pillar may have one LC for data collection from each pillar. The logical entity for data gathering can be implemented as a separate node or in a LR or LM. Communication schedules must be set up between leaf nodes and their LC to efficiently gather the different types of sensed data. Each data packet may include meta- information about its data, or the type of sensors could be encoded in its address during the address allocation. The data gathering entity can be programmed to trigger actuators installed in the infrastructure, when a certain threshold value has been reached. This type of application works based on both periodic and event- driven notifications. The data over or under a pre-defined threshold is meaningful to report. Event-driven data sensed on abnormal occurrences is time-critical and requires secure and reliable transmission. For energy conservation, all nodes may have periodic and long sleep modes but wake up on certain events. Due to the safety-critical data of the structure, authentication and security are important issues here. Only authenticated users MUST be allowed to access the data. Additional security SHOULD be provided at the LBR for restricting the access from outside of the LoWPAN. The LBR may take charge of authentication of LoWPAN nodes. Reliable and secure data transmission should be guaranteed. LBR - LC ----- LC ------ LC LBR: LoWPAN Border Router /| | | LC: Local Controller node n n n - n - n n - n n: LoWPAN Node /\ | | | | n n n - n n - n - n Figure 3: A LoWPAN with a mesh topology 3.3. Connected Home The "Connected" Home or "Smart" home is with no doubt an area where LoWPANs can be used to support an increasing number of services: o Home safety/security o Home Automation and Control Kim, et al. Expires January 29, 2011 [Page 14] Internet-Draft 6LoWPAN Design and Applications July 2010 o Healthcare (see above section) o Smart appliances and home entertainment systems In home environments LoWPAN networks typically comprise a few dozen and probably in the near future a few hundreds of nodes of various nature: sensors, actuators and connected objects. 3.3.1. A Use Case and its Requirements Example: Home Automation The home automation and control system LoWPAN offers a wide range of services: local or remote access from the Internet (via a secured edge router) to monitor the home (temperature, humidity, activation of remote video surveillance, status of the doors (locked or open), etc.) but also for home control (activate the air conditioning/ heating, door locks, sprinkler systems, etc.). Fairly sophisticated systems can also optimize the level of energy consumption thanks to a wide range of input from various sensors connected to the LoWPAN: light sensors, presence detection, temperature, etc. in order to control electric window shades, chillers, air flow control, air conditioning and heating with the objective to optimize energy consumption. With the emergence of "Smart Grid" applications, the LoWPAN may also have direct interactions with the Grid itself via the Internet of the Grid network to report the amount of KWatts that could be load shed (Home to Grid) and to receive dynamic load shedding information if/ when required (Grid to home): this application is also referred to as Demand-Response application. Another service known as Demand Side Management (DSM) could be provided by utilities to monitor and report to the user its energy consumption with a fine granularity (on a per device basis). Other inputs such as dynamic pricing can also be received by the user from the utility that can then turn on and off some appliances according to its local policy in order to reduce its energy bill. In terms of home safety and security, the LoWPAN is made of motion- and audio-sensors, sensors at doors and windows, and video cameras to which additional sensors can be added for safety (gas, water, CO, Radon, smoke detection). The LoWPAN typically comprises a few dozen of nodes forming an ad-hoc network with multi-hop routing since the nodes may not be in direct range. It is worth mentioning that the number of devices tends to grow considering the number of new applications for the home. In its most simple form, all nodes are static and communicate with a central control module but more sophisticated scenarios may also involve inter-device communication. Kim, et al. Expires January 29, 2011 [Page 15] Internet-Draft 6LoWPAN Design and Applications July 2010 For example, a motion/presence sensor may send a multicast message to a group of lights to be switched on, or a video camera will be activated sending a video stream to a gateway that can be received on a cell phone. Ergonomics in Connected Homes is a key and the LoWPAN must be self- managed and easy to install. Traffic patterns may greatly vary depending on the applicability and so does the level of reliability and QoS expected from the LoWPAN. Humidity sensing is typically not critical and requires no immediate action whereas tele-assistance or gas leak detection is critical and requires a high degree of reliability. Furthermore, although some actions may not involve critical data, still the response time and network delays must be on the order of a few hundreds of milliseconds to preserve the user experience (e.g. use a remote control to switch a light on). A minority of nodes are mobile (with slow motion). With the emergence of energy related applications it becomes crucial to preserve data confidentiality. Connected Home LoWPAN usually do not require multi- topology or QoS routing and fairly simple QoS mechanisms must be supported by the LoWPAN (the number of Class of Services is usually limited). Dominant parameters for home automation applications: o Deployment: multi-hop topologies o Mobility: some degree of mobility o Network Size: medium number of nodes, potentially high density o Power Source: mix of battery and mains-powered devices o Security Level: authentication and encryption required o Multi-hop communication: no requirement for multi-topology or QoS routing o Connectivity: intermittent (usage-dependent sleep modes) o QoS: support of limited QoS (small number of Class of Service) o Traffic Pattern: P2P (inter-device), P2MP and MP2P (polling) 3.3.2. 6LoWPAN Applicability In the home automation use case, the network topology is made of a mix of a battery operated and mains-powered nodes that both communication with each other and a LBR provides connectivities to Kim, et al. Expires January 29, 2011 [Page 16] Internet-Draft 6LoWPAN Design and Applications July 2010 the outside of LoWPAN for control management. In home network, installation and management must as extremely simple for the user. Link local IPv6 addresses can be used by nodes with no external communication and the LBR allocates routable addresses to communicate with other LoWPAN nodes not reachable over a single radio transmission. n --- n I: Internet | | LBR: LoWPAN Border Router Internet/ ------- LBR/LC -- n --- n ---- LC LC: Local controller node Utility network | | /|\ n: LoWPAN Node n ---- n n n n (outside) (home automation system) Figure 4: Home Automation scenario In some scenarios, the traffic will be sent to a LC for processing that may in turn decide of local actions (switch a light on, ...). In other scenarios, all devices will send their data to the LCs that may also act as the LBR for data processing and potential relay of data to outside of the LoWPAN. It does not mean that every device gets through the LC and LBR for communicating each other. For the sake of illustration, some of the data may be processed to trigger local action (e.g. switch off an appliance), simply store and sent once enough data has been accumulated (e.g. energy consumption for the past 6 hours for a set of appliances) or could trigger an alarm immediately sent to a datacenter (e.g. gas leak detection). Although in the majority of cases nodes within the LoPWAN will be in direct range, some nodes will reach the LBR/LC with a 2-3 hops path using Mesh Under or very likely a Route Over solution (with the emergence of several low power media such as low power PLC) in which case LoWPAN routers will be deployed in the home to interconnect the various IPv6 links. The home LoWPAN must be able to provide extremely reliable communication in support of some specific application (e.g. fire, gas leak detection, health monitoring) whereas other application may not be critical at all (e.g humidity monitoring). Similarly some information may require the use of security mechanisms for authentication, confidentiality. Kim, et al. Expires January 29, 2011 [Page 17] Internet-Draft 6LoWPAN Design and Applications July 2010 3.4. Healthcare LoWPANs are envisioned to be heavily used in healthcare environments. They have a big potential to ease the deployment of new services by getting rid of cumbersome wires and simplify patient care in hospitals and for home care. In healthcare environments, delayed or lost information may be a matter of life or death. Various systems, ranging from simple wearable remote controls for tele-assistance or intermediate systems with wearable sensor nodes monitoring various metrics to more complex systems for studying life dynamics, can be supported by LoWPANs. In the latter category, a large amount of data from various LoWPAN nodes can be collected: movement pattern observation, checks that medicaments have been taken, object tracking, and more. An example of such a deployment is described in [10] using the concept of Personal Networks. 3.4.1. A Use Case and its Requirements Example: healthcare at home by tele-assistance A senior citizen who lives alone wears one to few wearable LoWPAN nodes to measure heartbeat, pulse rate, etc. Dozens of LoWPAN nodes are densely installed at home for movement detection. A LBR at home will send the sensed information to a connected healthcare center. Portable base stations with LCDs may be used to check the data at home, as well. The different roles of devices have different duty- cycles, which affect node management. Multipath interference may often occur due to the mobility of the patients at home, where there are many walls and obstacles. Even during sleeping, the change of the body position may affect the radio propagation. Data is gathered both periodically and event-driven. In this application, event-driven data can be very time-critical. Thus, real-time and reliable transmission must be guaranteed. Privacy also becomes an serious issue in this case, as the sensed data is very personal. In addition, different data will be provided to the hospital system from what is given to a patient's family members. Role-based access control is needed to support such services, thus support of authorization and authentication is important. Dominant parameters in healthcare applications: Kim, et al. Expires January 29, 2011 [Page 18] Internet-Draft 6LoWPAN Design and Applications July 2010 o Deployment: pre-planned o Mobility: moderate (patient's mobility) o Network Size: small, high node density o Power Source: hybrid o Security Level: Data privacy and security MUST be provided. Encryption is required. Role based access control is required to be supported by light weight authentication mechanism o Multi-hop communicaton: multi-hop for homecare devices, star topology on patients body. Multipath interference due to walls and obstacles at home must be considered. o Connectivity: always on o QoS: high level of support (life and death implication), role- based o Traffic Pattern: MP2P/P2MP (data collection), P2P (local diagnostic) o Other issues: Plug-and-play configuration is required for mainly non-technical end-users. Real-time data acquisition and analysis are important. Efficient data management is needed for various devices which have different duty-cycles, and for role-based data control. Reliability and robustness of the network are also essential. 3.4.2. 6LoWPAN Applicability In this use case, the local network size is rather small (less than 10s of nodes). The home care system is statically configured with multi-hop paths and the patient's body network can be built as a star topology. The LBR at home is the sink node in the routing path from sources on the patient's body. A plug-and-play configuration is required. As the communication of the system is limited to a home environment, both 16-bit and 64-bit can be used for IPv6 link-local addresses [4]. An example topology is provided in Figure 5. Multi-hop communication can be achieved by either Mesh Under or Route Over mechanisms. When a Route Over routing mechanism is used, the routers deployed in the home environment will form a mesh of IPv6 links. In Mesh Under, more than one LMs in the LoWPAN play role in multi-hop transmission in link layer and in transmission multi-point traffic (multicast) to unicast method. In Route Over, LRs will Kim, et al. Expires January 29, 2011 [Page 19] Internet-Draft 6LoWPAN Design and Applications July 2010 handle multicast traffic to their LoWPAN link. The patient's body network can be simply configured as a star topology with a LC dealing with data aggregation and dynamic network attachment when the patient moves around at home. As multipath interference may often occur due to the patients' mobility at home, the deployment of LoWPAN nodes and transmission paths should be well considered. At home, some nodes can be installed with power- affluence status, and those LoWPAN nodes can be used for relaying points or data aggregation points. The sensed information MUST be maintained with the identification of the patient no matter if the patient visits the connected hospital or stays at home. If the patient's LoWPAN uses globally unique IPv6 address, the address can be used for the identification. However, it causes cost for privacy and security. The hospital LoWPAN where the patient's information is transferring needs to operate additional identification system together with strong authority and athentication mechanism. The connection between the LBR at home and the LBR at Hospital must be reliable and secure, as the data is privacy-critical. To achieve this, additional policy for security is recommended between the two LoWPAN. n - n I: Internet | | LBR: Edge Router LBR --- I -- LBR - n - n - LC LC: Local controller node /|\ | | /|\ n: LoWPAN Node .. . .. n -- n n n n (hospital) (home system) (patient) Figure 5: A mobile healthcare scenario. 3.5. Vehicle Telematics LoWPANs play an important role in intelligent transportation systems. Incorporated in roads, vehicles, and traffic signals, they contribute to the improvement of safety of transporting systems. Through traffic or air-quality monitoring, they increase the possibilities in terms of traffic flow optimization and help reducing road congestion. 3.5.1. A Use Case and its Requirements Example: Telematics As shown in Figure 6, scattered LoWPAN Nodes are included in roads during their construction for motion monitoring. When a car passes Kim, et al. Expires January 29, 2011 [Page 20] Internet-Draft 6LoWPAN Design and Applications July 2010 over these nodes, the possibility is then given to track the trajectory and velocity of cars for safety purposes. The lifetime of the LoWPAN Nodes incorporated into roads is expected to be as long as the life time of the roads (about 10 years). Multihop communication is possible between LoWPAN Nodes, and the network should be able to cope with the deterioration over time of the node density due to power failures. Sink nodes placed at the side of road are mains- powered, LoWPAN Nodes in the roads run on battery. Power savings schemes might intermittently disconnect the nodes. A rough estimate of 4 nodes per square meter is needed. Other applications may involve car-to-car communication for increased road safety. Dominant parameters in vehicle telematics applications: o Deployment: scattered, pre-planned o Mobility: none (road infrastructure), high (vehicle) o Network Size: large (road infrastructure), small (vehicle) o Power Source: hybrid o Security Level: low o Multi-hop communication: multi-hop, especially ad-hoc o Connectivity: intermittent o QoS: support of limited QoS o Traffic Pattern: mostly Point-to-Point (P2P), Point-to-Multi-Point (P2MP) 3.5.2. 6LoWPAN Applicability For this use case, the network topology includes fixed LBRs that are mains-powered and have a connection to high speed networks (e.g., Internet) in order to reach the transportation control center. These LBRs may be logically combined with LC as a data sink to gather sensed data from a number of LoWPAN Nodes inserted in the tarmac of the road. In the road infrastructure, a LoWPAN with one LBR forms a fixed network and the LoWPAN nodes are installed by manual optimization of their location. Static data paths to the data gathering point can be set in the commissioning phase. If the network does not use a Route Over mechanism, the 6LoWPAN mesh under forwarding is used. Forwarding/Routing tables are not changed unless a node failure Kim, et al. Expires January 29, 2011 [Page 21] Internet-Draft 6LoWPAN Design and Applications July 2010 occurs. +-----+ | LBR |----------------------------- LBR ... +-----+ (at the road side) -------|------------------------------ | n -- n --- n --- n +---|---+ LBR: LoWPAN Border Router / \ | | n-n-n | n: LoWPAN Node n n n +---|---+ (cars) -------------------------------------- Figure 6: Multi-hop LoWPAN combined with mobile star LoWPAN. 3.6. Agricultural Monitoring Accurate temporal and spatial monitoring can significantly increase agricultural productivity. Due to natural limitations, such as a farmers' inability to check the crop at all times of day or inadequate measurement tools, luck often plays a too large role in the success of harvests. Using a network of strategically placed sensors, indicators such as temperature, humidity, soil condition, can be automatically monitored without labor intensive field measurements. For example, sensor networks could provide precise information about crops in real time, enabling businesses to reduce water, energy, and pesticide usage and enhancing environment protection. The sensing data can be used to find optimal environments for the plants. In addition, the data on the planting condition can be saved by sensor tags, which can be used in supply chain management. 3.6.1. A Use Case and its Requirements Example: Automated Vineyard In a vineyard with medium to large geographical size, a number of 50 to 100 LC nodes are manually deployed in order to provide full signal coverage over the study area. An additional number of 100 to 1000 leaf nodes with (possibly heterogeneous) specialized sensors (i.e., humidity, temperature, soil condition, sunlight) are attached to the LCs in local wireless star topologies, periodically reporting measurements to the associated LCs. For example, in a 20-acre vineyard with 8 parcels of land, 10 LoWPAN Nodes are placed within each parcel to provide readings on temperature and soil moisture. The LoWPAN Nodes are able to support a multi-hop forwarding/routing scheme to enable data transmission to a sink node at the edge of the Kim, et al. Expires January 29, 2011 [Page 22] Internet-Draft 6LoWPAN Design and Applications July 2010 vineyard. Each of the 8 parcels contains one data aggregator to collect the sensed data. Localization is important for this type of LoWPAN where installed in a geographically large area, for pinning down where an event occurred, and for combining gathered data with their actual position. Using manual deployment, device addresses can be used for identifying the position and localization. For randomly deployed nodes, a localization algorithm needs to be applied. There might be various types of sensor devices deployed in a single LoWPAN, each providing raw data with different semantics. Thus, an additional method is required to correctly interpret sensor readings. Each data packet may include meta-information about its data, or a type of a sensor could be encoded in its address during address allocation. Dominant parameters in agricultural monitoring: o Deployment: pre-planned The nodes are installed outdoors or in a greenhouse with high exposure to water, soil, dust, in dynamic environments of moving people and machinery, with growing crop and foliage. LoWPAN nodes can be deployed in a pre-defined manner, considering the harsh environment. o Mobility: all static o Network Size: medium to large, low to medium density o Power Source: all nodes are battery-powered except the sink, or energy harvesting o Security Level: business-critical. Light-weight security or a global key management can be used depending on the business purpose. o Mutli-hop communication: mesh topology with local star connections. o Connectivity: intermittent (many sleeping nodes) o QoS: support of limited QoS (small number of Class of Service) o Traffic Pattern: Mainly MP2P/P2MP. P2P actuator triggering. Kim, et al. Expires January 29, 2011 [Page 23] Internet-Draft 6LoWPAN Design and Applications July 2010 o Other issues: Time synchronization among sensors are required, but the traffic interval may not be frequent (e.g. once in 30 minutes to 1 hour). 3.6.2. 6LoWPAN Applicability The network configuration in this use case might, in the most simple case, look like illustrated in Figure 7. This static scenario consists of one or more fixed LBR that are mains-powered and have a high-bandwidth connection to a backbone link, which might be placed in a control center, or connect to the Internet. The LBRs are strategically located at the border of vineyard parcels, acting as data sinks. A number of LCs are placed along a row of plants with individual LoWPAN nodes spread around them. While the LBRs implement the IPv6 Neighbor Discovery protocol (RFC 4861) to connect the outside of the LoWPAN, the LoWPAN Nodes operate a more energy-considering ND described in [6], which includes basic bootstrapping and address assignment. Each LBR can have predefined forward management information to a central data aggregation point, if necessary. The intermediate nodes must implement a multi-hop forwarding/routing protocol and they are responsible to transmit the measured data at the LoWPAN nodes to the LBRs. In this simplest case, the LRs or LMs can build static forwarding/routing paths, and all end-nodes can be placed in one radio hop distance from its forwarder. In more advanced setups, mesh routing is used for data distribution. LoWPAN nodes may send event-driven notifications when readings exceed certain thresholds, such as low soil humidity; which may automatically trigger a water sprinkler in the local environment. For increased energy efficiency, all LoWPAN Nodes are in periodic sleep state. However, the LCs need to be aware of sudden events from the leaf nodes. Their sleep periods should therefore be set to shorter intervals. Communication schedules must be set up between master and leaf nodes, and global time synchronization is needed to account for clock drift. Also, the result of data collection may activate actuators. Context- awareness, node identification and data collection on the application level are necessary. Kim, et al. Expires January 29, 2011 [Page 24] Internet-Draft 6LoWPAN Design and Applications July 2010 I | | n n n n n n n n n I: Internet | \|/ \|/ \|/ LBR: LoWPAN Border Router LBR----LC------LC------LC LC: Local Controller node | /|\ /|\ /|\ n: LoWPAN node | n n n n n n n n n | LBR ... Figure 7: An aligned multi-hop LoWPAN. Kim, et al. Expires January 29, 2011 [Page 25] Internet-Draft 6LoWPAN Design and Applications July 2010 4. Security Considerations Security requirements differ by use case. For example, industrial and structural monitoring applications are safety-critical. Secure transmission MUST be guaranteed, and only authenticated users MUST be able to access and handle the data. Lightweight key mechanisms can be used. In health care system, data privacy is an important issue. Encryption is required, and role-based access control is required to be supported by a proper authentication mechanism. Kim, et al. Expires January 29, 2011 [Page 26] Internet-Draft 6LoWPAN Design and Applications July 2010 5. Acknowledgements Thanks to David Cypher for giving more insight on the IEEE 802.15.4 standard and to Irene Fernandez for her review and valuable comments. Kim, et al. Expires January 29, 2011 [Page 27] Internet-Draft 6LoWPAN Design and Applications July 2010 6. References 6.1. Normative References [1] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [2] Narten, T., Nordmark, E., Simpson, W., and H. Soliman, "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861, September 2007. [3] Kushalnagar, N., Montenegro, G., and C. Schumacher, "IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals", RFC 4919, August 2007. [4] Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, "Transmission of IPv6 Packets over IEEE 802.15.4 Networks", RFC 4944, September 2007. [5] IEEE Computer Society, "IEEE Std. 802.15.4-2006 (as amended)", 2007. 6.2. Informative References [6] Shelby, Z., Chakrabarti, S., and E. Nordmark, "Neighbor Discovery Optimization for Low-power and Lossy Networks", draft-ietf-6lowpan-nd-11 (work in progress), July 2010. [7] Hui, J. and P. Thubert, "Compression Format for IPv6 Datagrams in 6LoWPAN Networks", draft-ietf-6lowpan-hc-08 (work in progress), July 2010. [8] Kim, E., Kaspar, D., Gomez, C., and C. Bormann, "Problem Statement and Requirements for 6LoWPAN Routing", draft-ietf-6lowpan-routing-requirements-06 (work in progress), March 2010. [9] Roemer, K. and F. Mattern, "The Design Space of Wireless Sensor Networks", December 2004. [10] den Hartog, F., Schmidt, J., and A. de Vries, "On the Potential of Personal Networks for Hospitals", May 2006. Kim, et al. Expires January 29, 2011 [Page 28] Internet-Draft 6LoWPAN Design and Applications July 2010 Authors' Addresses Eunsook Kim ETRI 161 Gajeong-dong Yuseong-gu Daejeon 305-700 Korea Phone: +82-42-860-6124 Email: eunah.ietf@gmail.com Dominik Kaspar Simula Research Laboratory Martin Linges v 17 Snaroya 1367 Norway Phone: +47-4748-9307 Email: dokaspar.ietf@gmail.com Nicolas G. Chevrollier TNO Brassersplein 2 P.O. Box 5050 Delft 2600 The Netherlands Phone: +31-15-285-7354 Email: nicolas.chevrollier@tno.nl JP Vasseur Cisco Systems, Inc 1414 Massachusetts Avenue Boxborough MA 01719 USA Phone: Email: jpv@cisco.com Kim, et al. Expires January 29, 2011 [Page 29]