Network Working Group X. Geng Internet-Draft M. Chen Intended status: Standards Track Huawei Expires: March 14, 2019 Z. Li China Mobile R. Rahman Cisco Systems September 10, 2018 DetNet Configuration YANG Model draft-geng-detnet-conf-yang-04 Abstract This document defines a YANG data model for Deterministic Networking (DetNet), which includes the DetNet topology YANG module, DetNet flow configuration YANG module and DetNet Transport QoS YANG Module. The YANG modules in this document conform to the Network Management Datastore Architecture (NMDA). Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on March 14, 2019. Geng, et al. Expires March 14, 2019 [Page 1] Internet-Draft DetNet Model September 2018 Copyright Notice Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Terminologies . . . . . . . . . . . . . . . . . . . . . . . . 4 3. DetNet Topology Model . . . . . . . . . . . . . . . . . . . . 4 3.1. DetNet Node Attributes . . . . . . . . . . . . . . . . . 5 3.2. DetNet Link Attributes . . . . . . . . . . . . . . . . . 6 3.3. DetNet Link Terminate Point Attributes . . . . . . . . . 7 4. DetNet Flow Configuration Model . . . . . . . . . . . . . . . 9 4.1. DetNet Service Proxy Configuration Attributes . . . . . . 9 4.2. DetNet Service Layer Configuration Attributes . . . . . . 10 4.3. DetNet Transport Layer Configuration Attributes . . . . . 12 4.4. DetNet Flow Configuration Example . . . . . . . . . . . . 13 5. DetNet Transport QoS Model . . . . . . . . . . . . . . . . . 14 6. DetNet Yang Structure . . . . . . . . . . . . . . . . . . . . 15 6.1. DetNet Topology Model Tree Diagram . . . . . . . . . . . 15 6.2. DetNet Flow Configuration Model Tree Diagram . . . . . . 17 7. DetNet YANG Model . . . . . . . . . . . . . . . . . . . . . . 22 7.1. DetNet Topology YANG Model . . . . . . . . . . . . . . . 22 7.2. DetNet Flow Configuration YANG Model . . . . . . . . . . 29 8. DetNet Configuration Model Classification . . . . . . . . . . 46 8.1. Fully Distributed Configuration Model . . . . . . . . . . 46 8.2. Fully Centralized Configuration Model . . . . . . . . . . 46 8.3. Hybrid Configuration Model . . . . . . . . . . . . . . . 47 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 48 10. Security Considerations . . . . . . . . . . . . . . . . . . . 48 11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 48 12. References . . . . . . . . . . . . . . . . . . . . . . . . . 48 12.1. Normative References . . . . . . . . . . . . . . . . . . 48 12.2. Informative References . . . . . . . . . . . . . . . . . 49 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 51 Geng, et al. Expires March 14, 2019 [Page 2] Internet-Draft DetNet Model September 2018 1. Introduction Deterministic Networking (DetNet) [I-D.ietf-detnet-architecture] is defined to provide high-quality network service with extremely low packet loss rate, bounded low latency and jitter. DetNet flow information is defined in[I-D.ietf-detnet-flow-information-model], and the DetNet models are categorized as: o Flow models: describe characteristics of data flows. These models describe in detail all relevant aspects of a flow that are needed to support the flow properly by the network between the source and the destination(s). o Service models: describe characteristics of services being provided for data flows over a network. These models can be treated as a network operator independent information model. o Configuration models: describe in detail the settings required on network nodes to serve a data flow properly. Service and flow information models are used between the user and the network operator. Configuration information models are used between the management/control plane entity of the network and the network nodes. They are shown in the Figure 1. User Network Operator flow/service +---+ model +---+ | | <---------------> | X | management/control +---+ +-+-+ plane entity ^ | configuration | model +------------+ v | | +-+ | v network +-+ v +-+ nodes +-+ +-+ +-+ Figure 1. Three Information Models This document defines DetNet configuration YANG [RFC7950] [RFC6991]data models, which include: Geng, et al. Expires March 14, 2019 [Page 3] Internet-Draft DetNet Model September 2018 o DetNet topology model DetNet topology model is designed for DetNet topology/ capability discovery and device configuration, it is an augmentation of the ietf-te-toplogy model [I-D.ietf-teas-yang-te-topo]. The detail of DetNet topology model is defined in Section 3. o DetNet flow configuration model DetNet flow model is designed for DetNet flow path configuration and flow status reporting. The detail of DetNet flow configuration model is defined in Section 4. o DetNet transport QoS model DetNet transport QoS model is designed for QoS attributes configuration of transport tunnels to achieve end-to-end bounded latency and zero congestion loss. The detail of DetNet transport QoS model is defined in Section 5. 2. Terminologies This documents uses the terminologies defined in [I-D.ietf-detnet-architecture]. 3. DetNet Topology Model A DetNet topology is composed of a set of DetNet nodes and DetNet links. DetNet nodes represent the network devices that can transport DetNet services, which are connected by DetNet links. A DetNet Link Terminate Point(LTP) is the connection point between a DetNet node and a DetNet link, which represents the port or interface of a network node. The concept of DetNet node/link/LTP are similar as TE node/link/LTP that are defined in [I-D.ietf-teas-yang-te-topo]. Figure 2 shows a simple DetNet topology: A is a DetNet node, B is DetNet a LTP, and C is a DetNet link. +---+ +---+ | A |o(B)--(C)--| | +---+ +---+ Figure 2. An example of DetNet Topology DetNet topology model (ietf-detnet-topology) augments ietf-te- topology model [I-D.ietf-teas-yang-te-topo] to cover the following Geng, et al. Expires March 14, 2019 [Page 4] Internet-Draft DetNet Model September 2018 attributes, which are necessary for supporting DetNet congestion protection and service protection functions: o Bandwidth related attributes (e.g., bandwidth reserved for DetNet); o Buffer/queue management related attributes (e.g., queue management algorithm, etc.); o PREOF (Packet Replication, Ordering and Elimination Function) capabilities and parameters (e.g., maximum out-of-order packets, etc.); o Delay related attributes (e.g., node processing delay, queuing delay, link delay, etc.); The above attributes are categorized into three types: node attributes, link attributes and LTP attributes. The detailed descriptions and model definitions are specified in section 4.1, 4.2 and 4.3, respectively. 3.1. DetNet Node Attributes Section 4.3 of [I-D.finn-detnet-bounded-latency] gives a DetNet time model, which defines that the delay within a node includes five parts: processing delay, regulation delay, queuing delay, output delay and preemption delay. The processing delay, queuing delay and regulation delay are variable in general, but for DetNet, these delays should be bounded, which is the basic assumption of deterministic networking. These bounded delay parameters are necessary to perform DetNet path computation. Among this delay attributes, processing delay and regulation delay are node relevant, and the queuing delay is LTP relevant. In addition, in order to simplify the model and implementation, the processing delay and regulation delay are combined as processing delay, and the preemption delay is included in queuing delay. [Editor notes: more comments and inputs need here]. For the DetNet node attributes, the following variables are introduced: o Maximum DetNet packet processing delay o Minimum DetNet packet processing delay o Maximum DetNet packet processing delay variation The modeling structure is shown below: Geng, et al. Expires March 14, 2019 [Page 5] Internet-Draft DetNet Model September 2018 augment /nw:networks/nw:network/nw:node/tet:te/tet:te-node-attributes: +--rw detnet-node-attributes +--rw minimum-packet-processing-delay? uint32 +--rw maximum-packet-processing-delay? uint32 +--rw maximum-packet-processing-delay-variation? uint32 3.2. DetNet Link Attributes DetNet link attributes include link delay and link bandwidth for DetNet. This document introduces the following link related attributes: o Link delay: link delay is a constant that only depends on the physical connection. It has been defined in ietf-te-topology [I-D.ietf-teas-yang-te-topo], and DetNet can reuse it directly. o Maximum DetNet reservable bandwidth: the maximum reservable bandwidth that is allocated to DetNet. For a 10G link, if 50% of the bandwidth is allocated to DetNet, then the maximum DetNet reservable bandwidth is 5G. That means there are 5G bandwidth that can be used by DetNet flows. o Reserved DetNet bandwidth: the bandwidth that has been reserved for DetNet flows. o Available DetNet bandwidth: the bandwidth that is available for new DetNet flows. The DetNet link attributes are modeled within a link, and the YANG module structure is shown below: augment /nw:networks/nw:network/nt:link/tet:te/tet:te-link-attributes: +--rw detnet-link-attributes +--rw maximum-reservable-bandwidth | +--rw te-bandwidth | +--rw (technology)? | +--:(generic) | +--rw generic? te-bandwidth +--rw reserved-detnet-bandwidth | +--rw te-bandwidth | +--rw (technology)? | +--:(generic) | +--rw generic? te-bandwidth +--rw available-detnet-bandwidth +--rw te-bandwidth +--rw (technology)? +--:(generic) +--rw generic? te-bandwidth Geng, et al. Expires March 14, 2019 [Page 6] Internet-Draft DetNet Model September 2018 3.3. DetNet Link Terminate Point Attributes The concept of LTP is introduced in [I-D.ietf-teas-yang-te-topo], and this section introduces attributes for DetNet LTP. PREOF (Packet Replication/Elimination/Ordering Function) is for DetNet service protection, which includes : o In-order delivery function: defined in Section 3.2.2.1 of [I-D.ietf-detnet-architecture] o Packet replication function: defined in Section 3.2.2.2 of [I-D.ietf-detnet-architecture] o Packet elimination function: defined in Section 3.2.2.3 of [I-D.ietf-detnet-architecture] The above functions are modeled as a set of capabilities and relevant parameters, which are listed below: o in-order-capability: indicates whether a LTP has the in-order delivery capability. o maximum-number-of-out-of-order-packets: indicates the maximum number of out-of-order packets that an LTP can support, it depends on the reserved buffer size for packet reordering. o replication-capability: indicates whether a LTP has the packet replication capability. o elimination-capability: indicates whether a LTP has the packet elimination capability. In addition, DetNet LTP also includes queuing management algorithms and queuing delay attributes. In the context of DetNet, the delay of queuing is bounded, and the bound depends on what queuing management method is used and how many buffers are allocated. More information can be found in [I-D.finn-detnet-bounded-latency]. Queuing related attributes are listed below: o queuing-algorithm-capabilities: it is modeled as a list that includes all queuing algorithms that a LTP supports. o detnet-queues: it's modeled as a list that includes all queues of a DetNet LTP. For each queue, it has the following attributes: o queue-identifier: an identifier of a queue. It could be an internal identifier that is only used within a node. Or it could Geng, et al. Expires March 14, 2019 [Page 7] Internet-Draft DetNet Model September 2018 be used by a centralized controller to specify in which specific queue a flow/packet is required to enter. o queue-buffer-size: the size of a queue with unit of bytes. o enabled-queuing-algorithm: indicates what queuing management algorithm is enabled. o maximum-queuing-delay: the maximum queuing delay that a packet will undergo when transmitted through the queue. o minimum-queuing-delay: the minimum queuing delay that a packet will undergo when transmitted through the queue. o maximum-queuing-delay-variation: the maximum queuing delay variation that a packet will undergo when transmitted the queue. The DetNet LTP attributes are modeled with a LTP, the YANG module structure is shown below: augment /nw:networks/nw:network/nw:node/nt:termination-point/tet:te: +--rw detnet-terminate-point-attributes +--rw elimination-capability? boolean +--rw replication-capability? boolean +--rw in-ordering-capability | +--rw in-ordering-capability? boolean | +--rw maximum-out-of-order-packets? uint32 +--rw queuing-algorithm-capabilities | +--rw credit-based-shaping? boolean | +--rw time-aware-shaping? boolean | +--rw cyclic-queuing-and-forwarding? boolean | +--rw asynchronous-traffic-shaping? boolean +--rw queues* [queue-identifier] +--rw queue-identifier uint32 +--rw queue-buffer-size? uint32 +--rw enabled-queuing-algorithm | +--rw credit-based-shaping? boolean | +--rw time-aware-shaping? boolean | +--rw cyclic-queuing-and-forwarding? boolean | +--rw asynchronous-traffic-shaping? boolean +--rw minimum-queuing-delay? uint32 +--rw maximum-queuing-delay? uint32 +--rw maximum-queuing-delay-variation? uint32 Geng, et al. Expires March 14, 2019 [Page 8] Internet-Draft DetNet Model September 2018 4. DetNet Flow Configuration Model DetNet flow configuration includes DetNet Service Proxy configuration, DetNet Service Layer configuration and DetNet Transport Layer configuration. The corresponding attributes used in different layers are defined in Section 4.1, 4.2, 4.3, respectively. Section 4.4 gives a simple example on how to use these attributes for DetNet flow configuration. 4.1. DetNet Service Proxy Configuration Attributes DetNet service proxy is responsible for mapping between application flows and DetNet flows at the edge node(egress/ingress node). Where the application flows can be either layer 2 or layer 3 flows. To identify a flow at the User Network Interface (UNI), as defined in [I-D.ietf-detnet-flow-information-model], the following flow attributes are introduced: o DetNet L3 Flow Identification, refers to Section 7.1.1 of [I-D.ietf-detnet-flow-information-model] o DetNet L2 Flow Identification, refers to Section 7.1.2 of [I-D.ietf-detnet-flow-information-model] DetNet service proxy can also do flow filtering and policing at the ingress to prevent the misbehaviored flows from going into the network, which needs: o Traffic Specification, refers to Section 7.2 of [I-D.ietf-detnet-flow-information-model] The YANG module structure is shown below: Geng, et al. Expires March 14, 2019 [Page 9] Internet-Draft DetNet Model September 2018 +--rw client-flow* [flow-id] | +--rw flow-id uint32 | +--rw (flow-type)? | | +--:(l2-flow-identfication) | | | +--rw source-mac-address? yang:mac-address | | | +--rw destination-mac-address? yang:mac-address | | | +--rw ethertype? eth:ethertype | | | +--rw vlan-id? uint16 | | | +--rw pcp | | +--:(l3-flow-identification) | | +--rw (ip-flow-type)? | | | +--:(ipv4) | | | | +--rw src-ipv4-address? inet:ipv4-address | | | | +--rw dest-ipv4-address? inet:ipv4-address | | | | +--rw dscp? uint8 | | | +--:(ipv6) | | | +--rw src-ipv6-address? inet:ipv6-address | | | +--rw dest-ipv6-address? inet:ipv6-address | | | +--rw traffic-class? uint8 | | | +--rw flow-label? inet:ipv6-flow-label | | +--rw source-port? inet:port-number | | +--rw destination-port? inet:port-number | | +--rw protocol? uint8 | +--rw traffic-specification | +--rw interval? uint32 | +--rw max-packets-per-interval? uint32 | +--rw max-payload-size? uint32 | +--rw average-packets-per-interval? uint32 | +--rw average-payload-size? uint32 4.2. DetNet Service Layer Configuration Attributes DetNet service functions, e.g., DetNet tunnel initialization/ termination and service protection, are provided in DetNet service layer. To support these functions, the following service attributes need to be configured: o DetNetwork flow identification, refers to Section 7.1.3 of [I-D.ietf-detnet-flow-information-model]. o Service function indication, indicates which service function will be invoked at a DetNet edge, relay node or end station. (DetNet tunnel initialization or termination are default functions in DetNet service layer, so there is no need for explicit indication.) o Flow Rank, refers to Section 7.3 of [I-D.ietf-detnet-flow-information-model]. Geng, et al. Expires March 14, 2019 [Page 10] Internet-Draft DetNet Model September 2018 o Service Rank, refers to Section 7.4 of [I-D.ietf-detnet-flow-information-model]. o Service encapsulation, refers to Section 6.2 of [I-D.ietf-detnet-dp-sol-mpls] o Transport encapsulation, refers to Section 6.2 of [I-D.ietf-detnet-dp-sol-mpls]and Section 3 of [I-D.ietf-detnet-dp-sol-ip] The YANG module structure is shown below: | +--rw relay-node | +--rw name? string | +--rw flow-rank | +--rw service-rank | +--rw in-segment* [in-segment-id] | | +--rw in-segment-id uint32 | | +--rw (flow-type)? | | | +--:(IP) | | | | +--rw (ip-flow-type)? | | | | | +--:(ipv4) | | | | | | +--rw src-ipv4-address? inet:ipv4-address | | | | | | +--rw dest-ipv4-address? inet:ipv4-address | | | | | | +--rw dscp? uint8 | | | | | +--:(ipv6) | | | | | +--rw src-ipv6-address? inet:ipv6-address | | | | | +--rw dest-ipv6-address? inet:ipv6-address | | | | | +--rw traffic-class? uint8 | | | | | +--rw flow-label? inet:ipv6-flow-label | | | | +--rw source-port? inet:port-number | | | | +--rw destination-port? inet:port-number | | | | +--rw protocol? uint8 | | | +--:(MPLS) | | | +--rw service-label uint32 | | +--rw service-function? service-function-type | +--rw out-segment* [out-segment-id] | +--rw out-segment-id uint32 | +--rw detnet-service-encapsulation | | +--rw service-label uint32 | | +--rw control-word uint32 | +--rw detnet-transport-encapsulation | +--rw (tunnel-type)? | | +--:(IPv4) | | | +--rw ipv4-encaplustion | | | +--rw src-ipv4-address inet:ipv4-address | | | +--rw dest-ipv4-address inet:ipv4-address | | | +--rw protocol uint8 Geng, et al. Expires March 14, 2019 [Page 11] Internet-Draft DetNet Model September 2018 | | | +--rw ttl? uint8 | | | +--rw dscp? uint8 | | +--:(IPv6) | | | +--rw ipv6-encaplustion | | | +--rw src-ipv6-address inet:ipv6-address | | | +--rw dest-ipv6-address inet:ipv6-address | | | +--rw next-header uint8 | | | +--rw traffic-class? uint8 | | | +--rw flow-label? inet:ipv6-flow-label | | | +--rw hop-limit? uint8 | | +--:(MPLS) | | +--rw mpls-encaplustion | | +--rw label-operations* [label-oper-id] | | +--rw label-oper-id uint32 | | +--rw (label-actions)? | | +--:(label-push) | | | +--rw label-push | | | +--rw label uint32 | | | +--rw s-bit? boolean | | | +--rw tc-value? uint8 | | | +--rw ttl-value? uint8 | | +--:(label-swap) | | +--rw label-swap | | +--rw out-label uint32 | | +--rw ttl-action? ttl-action-definition | +--rw interval? uint32 | +--rw max-packets-per-interval? uint32 | +--rw max-payload-size? uint32 | +--rw average-packets-per-interval? uint32 | +--rw average-payload-size? uint32 4.3. DetNet Transport Layer Configuration Attributes As defined in [I-D.ietf-detnet-architecture], DetNet transport layer optionally provides congestion protection for DetNet flows over paths provided by the underlying network. Explicit route is another mechanism that is used by DetNet to avoid temporary interruptions caused by the convergence of routing or bridging protocols, and it is also implemented at the DetNet transport layer. To support congestion protection and explicit route, the following transport layer related attributes are necessary: o Traffic Specification, refers to Section 7.2 of [I-D.ietf-detnet-flow-information-model]. It may used for bandwidth reservation, flow shaping, filtering and policing. Geng, et al. Expires March 14, 2019 [Page 12] Internet-Draft DetNet Model September 2018 o Explicit path, existing explicit route mechanisms can be reused. For example, if Segment Routing (SR) tunnel is used as the transport tunnel, the configuration is mainly at the ingress node of the transport layer; if the static MPLS tunnel is used as the transport tunnel, the configurations need to be at every transit node along the path; for pure IP based transport tunnel, it's similar to the static MPLS case. The YANG module structure is shown below: | +--rw transit-node | +--rw interval? uint32 | +--rw max-packets-per-interval? uint32 | +--rw max-payload-size? uint32 | +--rw average-packets-per-interval? uint32 | +--rw average-payload-size? uint32 The parameters for DetNet transport QoS are defined in Section 5. 4.4. DetNet Flow Configuration Example This section gives an example about how to implement an end-2-end DetNet service with the collaboration of DetNet proxy, service and transport layers. To simplify the explanation, several terms are introduced. This document defines DetNet Service Proxy Instance (DSPI), DetNet Service Instance (DSI) and DetNet Transport Instance for end-to-end DetNet flow configuration as showed in Figure 4. DSPI 1 at Edge Node 1 (E1) maps an application flow to a DetNet Flow (DF1), which is transmitted over a DetNet tunnel (Tn1). In DSI 2 of Relay Node 1 (R1), DetNet Flow 1(DF1) was replicated into two member flows: DetNet Flow 2 (DF2) transmitted by DetNet Tunnel 2 (Tnl2) and DetNet Flow 3 (DF3) by DetNet Tunnel 3(Tnl3). In DSPI 3 of Edge Node 2 (E2), DetNet Flow 2 (DF2) and DetNet Flow 3(DF3) were merged and mapped to application flow used by CE2. Geng, et al. Expires March 14, 2019 [Page 13] Internet-Draft DetNet Model September 2018 DF: DetNet Flow DSPI: DetNet Service Proxy Instance DSI: DetNet Service Instance DTI: DetNet Transport Instance Tnl: Tunnel |<------- End to End DetNet Service ------>| | DetNet DetNet | (AC) | |<-Tnl->| |<-Tnl->| | (AC) End | V V 1 V V 2/3 V V | End System | +--------+ +--------+ +--------+ | System +---+ | | E1 |=======| R1 |=======| E2 | | +---+ | |--|----|--------| |--------| |--------|---|---| | |CE1| | | DSPI 1 | | | | DSPI 2 | | |CE2| | | |+-------+ | | +-------+| | | +---+ || DSI 1 | | DSI 2 | | DSI 3 || +---+ || + | +------+ | || || +-----+ | |DTI 2 |..DF2..| || || |DTI 1|..DF1..| +------+ | || || +-----+ | |DTI 3 |..DF3..| || |+-------+ | +------+ +-------+| +--------+=======+--------+=======+--------+ Edge Node Relay Node Edge Node | | |<-------- DetNet Service --------->| Figure 3. End-to-end DetNet Flow Configuration 5. DetNet Transport QoS Model The YANG data model of transport QoS is very important to achieve end-to-end bounded latency and zero congestion loss. There are three possible methods to deal with the DetNet transport QoS YANG: 1. DetNet service is not aware of any QoS/queuing/bounded-latency information, and all relative parameters are defined in separate YANG models; 2. DetNet service is not aware of any of Qos/queuing/bounded-latency information, but it should maintain an interface to the corresponding YANG models; 3. DetNet service should be aware of the Qos/queuing/bounded-latency information, because some Qos/queuing/bounded-latency mechanisms are required to be configured with flow information; Geng, et al. Expires March 14, 2019 [Page 14] Internet-Draft DetNet Model September 2018 How to define transport QoS YANG is still under discussion and the transport QoS YANG model is not included in the current version of the draft. [Editor notes: more comments and inputs need here]. 6. DetNet Yang Structure 6.1. DetNet Topology Model Tree Diagram Geng, et al. Expires March 14, 2019 [Page 15] Internet-Draft DetNet Model September 2018 module: ietf-detnet-topology augment /nw:networks/nw:network/nw:network-types/tet:te-topology: +--rw detnet-topology! augment /nw:networks/nw:network/nw:node/tet:te/tet:te-node-attributes: +--rw detnet-node-attributes +--rw minimum-packet-processing-delay? uint32 +--rw maximum-packet-processing-delay? uint32 +--rw maximum-packet-processing-delay-variation? uint32 augment /nw:networks/nw:network/nt:link/tet:te/tet:te-link-attributes: +--rw detnet-link-attributes +--rw maximum-reservable-bandwidth | +--rw te-bandwidth | +--rw (technology)? | +--:(generic) | +--rw generic? te-bandwidth +--rw reserved-detnet-bandwidth | +--rw te-bandwidth | +--rw (technology)? | +--:(generic) | +--rw generic? te-bandwidth +--rw available-detnet-bandwidth +--rw te-bandwidth +--rw (technology)? +--:(generic) +--rw generic? te-bandwidth augment /nw:networks/nw:network/nw:node/nt:termination-point/tet:te: +--rw detnet-terminate-point-attributes +--rw elimination-capability? boolean +--rw replication-capability? boolean +--rw in-ordering-capability | +--rw in-ordering-capability? boolean | +--rw maximum-out-of-order-packets? uint32 +--rw queuing-algorithm-capabilities | +--rw credit-based-shaping? boolean | +--rw time-aware-shaping? boolean | +--rw cyclic-queuing-and-forwarding? boolean | +--rw asynchronous-traffic-shaping? boolean +--rw queues* [queue-identifier] +--rw queue-identifier uint32 +--rw queue-buffer-size? uint32 +--rw enabled-queuing-algorithm | +--rw credit-based-shaping? boolean | +--rw time-aware-shaping? boolean | +--rw cyclic-queuing-and-forwarding? boolean | +--rw asynchronous-traffic-shaping? boolean +--rw minimum-queuing-delay? uint32 +--rw maximum-queuing-delay? uint32 +--rw maximum-queuing-delay-variation? uint32 Geng, et al. Expires March 14, 2019 [Page 16] Internet-Draft DetNet Model September 2018 6.2. DetNet Flow Configuration Model Tree Diagram module: ietf-detnet-flow-config +--rw detnet-flow +--rw (detnet-node-role)? +--:(transit-node) | +--rw transit-node | +--rw interval? uint32 | +--rw max-packets-per-interval? uint32 | +--rw max-payload-size? uint32 | +--rw average-packets-per-interval? uint32 | +--rw average-payload-size? uint32 +--:(relay-node) | +--rw relay-node | +--rw name? string | +--rw flow-rank | +--rw service-rank | +--rw in-segment* [in-segment-id] | | +--rw in-segment-id uint32 | | +--rw (flow-type)? | | | +--:(IP) | | | | +--rw (ip-flow-type)? | | | | | +--:(ipv4) | | | | | | +--rw src-ipv4-address? inet:ipv4-address | | | | | | +--rw dest-ipv4-address? inet:ipv4-address | | | | | | +--rw dscp? uint8 | | | | | +--:(ipv6) | | | | | +--rw src-ipv6-address? inet:ipv6-address | | | | | +--rw dest-ipv6-address? inet:ipv6-address | | | | | +--rw traffic-class? uint8 | | | | | +--rw flow-label? inet:ipv6-flow-label | | | | +--rw source-port? inet:port-number | | | | +--rw destination-port? inet:port-number | | | | +--rw protocol? uint8 | | | +--:(MPLS) | | | +--rw service-label uint32 | | +--rw service-function? service-function-type | +--rw out-segment* [out-segment-id] | +--rw out-segment-id uint32 | +--rw detnet-service-encapsulation | | +--rw service-label uint32 | | +--rw control-word uint32 | +--rw detnet-transport-encapsulation | +--rw (tunnel-type)? | | +--:(IPv4) | | | +--rw ipv4-encaplustion | | | +--rw src-ipv4-address inet:ipv4-address | | | +--rw dest-ipv4-address inet:ipv4-address Geng, et al. Expires March 14, 2019 [Page 17] Internet-Draft DetNet Model September 2018 | | | +--rw protocol uint8 | | | +--rw ttl? uint8 | | | +--rw dscp? uint8 | | +--:(IPv6) | | | +--rw ipv6-encaplustion | | | +--rw src-ipv6-address inet:ipv6-address | | | +--rw dest-ipv6-address inet:ipv6-address | | | +--rw next-header uint8 | | | +--rw traffic-class? uint8 | | | +--rw flow-label? inet:ipv6-flow-label | | | +--rw hop-limit? uint8 | | +--:(MPLS) | | +--rw mpls-encaplustion | | +--rw label-operations* [label-oper-id] | | +--rw label-oper-id uint32 | | +--rw (label-actions)? | | +--:(label-push) | | | +--rw label-push | | | +--rw label uint32 | | | +--rw s-bit? boolean | | | +--rw tc-value? uint8 | | | +--rw ttl-value? uint8 | | +--:(label-swap) | | +--rw label-swap | | +--rw out-label uint32 | | +--rw ttl-action? ttl-action-definition | +--rw interval? uint32 | +--rw max-packets-per-interval? uint32 | +--rw max-payload-size? uint32 | +--rw average-packets-per-interval? uint32 | +--rw average-payload-size? uint32 +--:(edge-node) | +--rw edge-node | +--rw client-flow* [flow-id] | | +--rw flow-id uint32 | | +--rw (flow-type)? | | | +--:(l2-flow-identfication) | | | | +--rw source-mac-address? yang:mac-address | | | | +--rw destination-mac-address? yang:mac-address | | | | +--rw ethertype? eth:ethertype | | | | +--rw vlan-id? uint16 | | | | +--rw pcp | | | +--:(l3-flow-identification) | | | +--rw (ip-flow-type)? | | | | +--:(ipv4) | | | | | +--rw src-ipv4-address? inet:ipv4-address | | | | | +--rw dest-ipv4-address? inet:ipv4-address | | | | | +--rw dscp? uint8 Geng, et al. Expires March 14, 2019 [Page 18] Internet-Draft DetNet Model September 2018 | | | | +--:(ipv6) | | | | +--rw src-ipv6-address? inet:ipv6-address | | | | +--rw dest-ipv6-address? inet:ipv6-address | | | | +--rw traffic-class? uint8 | | | | +--rw flow-label? inet:ipv6-flow-label | | | +--rw source-port? inet:port-number | | | +--rw destination-port? inet:port-number | | | +--rw protocol? uint8 | | +--rw traffic-specification | | +--rw interval? uint32 | | +--rw max-packets-per-interval? uint32 | | +--rw max-payload-size? uint32 | | +--rw average-packets-per-interval? uint32 | | +--rw average-payload-size? uint32 | +--rw detnet-service-instance | +--rw name? string | +--rw flow-rank | +--rw service-rank | +--rw in-segment* [in-segment-id] | | +--rw in-segment-id uint32 | | +--rw (flow-type)? | | | +--:(IP) | | | | +--rw (ip-flow-type)? | | | | | +--:(ipv4) | | | | | | +--rw src-ipv4-address? inet:ipv4-address | | | | | | +--rw dest-ipv4-address? inet:ipv4-address | | | | | | +--rw dscp? uint8 | | | | | +--:(ipv6) | | | | | +--rw src-ipv6-address? inet:ipv6-address | | | | | +--rw dest-ipv6-address? inet:ipv6-address | | | | | +--rw traffic-class? uint8 | | | | | +--rw flow-label? inet:ipv6-flow-label | | | | +--rw source-port? inet:port-number | | | | +--rw destination-port? inet:port-number | | | | +--rw protocol? uint8 | | | +--:(MPLS) | | | +--rw service-label uint32 | | +--rw service-function? service-function-type | +--rw out-segment* [out-segment-id] | +--rw out-segment-id uint32 | +--rw detnet-service-encapsulation | | +--rw service-label uint32 | | +--rw control-word uint32 | +--rw detnet-transport-encapsulation | +--rw (tunnel-type)? | | +--:(IPv4) | | | +--rw ipv4-encaplustion | | | +--rw src-ipv4-address inet:ipv4-address Geng, et al. Expires March 14, 2019 [Page 19] Internet-Draft DetNet Model September 2018 | | | +--rw dest-ipv4-address inet:ipv4-address | | | +--rw protocol uint8 | | | +--rw ttl? uint8 | | | +--rw dscp? uint8 | | +--:(IPv6) | | | +--rw ipv6-encaplustion | | | +--rw src-ipv6-address inet:ipv6-address | | | +--rw dest-ipv6-address inet:ipv6-address | | | +--rw next-header uint8 | | | +--rw traffic-class? uint8 | | | +--rw flow-label? inet:ipv6-flow-label | | | +--rw hop-limit? uint8 | | +--:(MPLS) | | +--rw mpls-encaplustion | | +--rw label-operations* [label-oper-id] | | +--rw label-oper-id uint32 | | +--rw (label-actions)? | | +--:(label-push) | | | +--rw label-push | | | +--rw label uint32 | | | +--rw s-bit? boolean | | | +--rw tc-value? uint8 | | | +--rw ttl-value? uint8 | | +--:(label-swap) | | +--rw label-swap | | +--rw out-label uint32 | | +--rw ttl-action? ttl-action-definition | +--rw interval? uint32 | +--rw max-packets-per-interval? uint32 | +--rw max-payload-size? uint32 | +--rw average-packets-per-interval? uint32 | +--rw average-payload-size? uint32 +--:(end-station) +--rw end-station +--rw client-flow* [flow-id] | +--rw flow-id uint32 | +--rw (flow-type)? | | +--:(l2-flow-identfication) | | | +--rw source-mac-address? yang:mac-address | | | +--rw destination-mac-address? yang:mac-address | | | +--rw ethertype? eth:ethertype | | | +--rw vlan-id? uint16 | | | +--rw pcp | | +--:(l3-flow-identification) | | +--rw (ip-flow-type)? | | | +--:(ipv4) | | | | +--rw src-ipv4-address? inet:ipv4-address | | | | +--rw dest-ipv4-address? inet:ipv4-address Geng, et al. Expires March 14, 2019 [Page 20] Internet-Draft DetNet Model September 2018 | | | | +--rw dscp? uint8 | | | +--:(ipv6) | | | +--rw src-ipv6-address? inet:ipv6-address | | | +--rw dest-ipv6-address? inet:ipv6-address | | | +--rw traffic-class? uint8 | | | +--rw flow-label? inet:ipv6-flow-label | | +--rw source-port? inet:port-number | | +--rw destination-port? inet:port-number | | +--rw protocol? uint8 | +--rw traffic-specification | +--rw interval? uint32 | +--rw max-packets-per-interval? uint32 | +--rw max-payload-size? uint32 | +--rw average-packets-per-interval? uint32 | +--rw average-payload-size? uint32 +--rw detnet-service-instance +--rw name? string +--rw flow-rank +--rw service-rank +--rw in-segment* [in-segment-id] | +--rw in-segment-id uint32 | +--rw (flow-type)? | | +--:(IP) | | | +--rw (ip-flow-type)? | | | | +--:(ipv4) | | | | | +--rw src-ipv4-address? inet:ipv4-address | | | | | +--rw dest-ipv4-address? inet:ipv4-address | | | | | +--rw dscp? uint8 | | | | +--:(ipv6) | | | | +--rw src-ipv6-address? inet:ipv6-address | | | | +--rw dest-ipv6-address? inet:ipv6-address | | | | +--rw traffic-class? uint8 | | | | +--rw flow-label? inet:ipv6-flow-label | | | +--rw source-port? inet:port-number | | | +--rw destination-port? inet:port-number | | | +--rw protocol? uint8 | | +--:(MPLS) | | +--rw service-label uint32 | +--rw service-function? service-function-type +--rw out-segment* [out-segment-id] +--rw out-segment-id uint32 +--rw detnet-service-encapsulation | +--rw service-label uint32 | +--rw control-word uint32 +--rw detnet-transport-encapsulation +--rw (tunnel-type)? | +--:(IPv4) | | +--rw ipv4-encaplustion Geng, et al. Expires March 14, 2019 [Page 21] Internet-Draft DetNet Model September 2018 | | +--rw src-ipv4-address inet:ipv4-address | | +--rw dest-ipv4-address inet:ipv4-address | | +--rw protocol uint8 | | +--rw ttl? uint8 | | +--rw dscp? uint8 | +--:(IPv6) | | +--rw ipv6-encaplustion | | +--rw src-ipv6-address inet:ipv6-address | | +--rw dest-ipv6-address inet:ipv6-address | | +--rw next-header uint8 | | +--rw traffic-class? uint8 | | +--rw flow-label? inet:ipv6-flow-label | | +--rw hop-limit? uint8 | +--:(MPLS) | +--rw mpls-encaplustion | +--rw label-operations* [label-oper-id] | +--rw label-oper-id uint32 | +--rw (label-actions)? | +--:(label-push) | | +--rw label-push | | +--rw label uint32 | | +--rw s-bit? boolean | | +--rw tc-value? uint8 | | +--rw ttl-value? uint8 | +--:(label-swap) | +--rw label-swap | +--rw out-label uint32 | +--rw ttl-action? ttl-action-definition +--rw interval? uint32 +--rw max-packets-per-interval? uint32 +--rw max-payload-size? uint32 +--rw average-packets-per-interval? uint32 +--rw average-payload-size? uint32 7. DetNet YANG Model 7.1. DetNet Topology YANG Model file "ietf-detnet-topology@20180910.yang" module ietf-detnet-topology { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-detnet-topology"; prefix "detnet-topology"; import ietf-te-types { prefix "te-types"; } Geng, et al. Expires March 14, 2019 [Page 22] Internet-Draft DetNet Model September 2018 import ietf-te-topology { prefix "tet"; } import ietf-network { prefix "nw"; } import ietf-network-topology { prefix "nt"; } organization "IETF Deterministic Networking(DetNet)Working Group"; contact "WG Web: WG List: WG Chair: Lou Berger Janos Farkas Editor: Xuesong Geng Editor: Mach Chen Editor: Zhenqiang Li Editor: Reshad Rahman "; description "This YANG module augments the 'ietf-te-topology' module with DetNet related capabilities and parameters."; revision "2018-09-10" { description "Initial revision"; reference "RFC XXXX: draft-geng-detnet-config-yang-05"; } Geng, et al. Expires March 14, 2019 [Page 23] Internet-Draft DetNet Model September 2018 grouping detnet-queuing-algorithms { description "Candidate DetNet queuing management algorithms."; leaf credit-based-shaping { type boolean; description "Indicates whether credit based shaping is supported."; reference "IEEE P802.1 Qav"; } leaf time-aware-shaping { type boolean; description "Indicates whether time aware shaping is supported."; reference "IEEE P802.1 Qbv"; } leaf cyclic-queuing-and-forwarding { type boolean; description "Indicates whether cyclic queuing and forwarding is supported."; reference "IEEE P802.1 Qch"; } leaf asynchronous-traffic-shaping { type boolean; description "Indicates whether asynchronous traffic shaping is supported."; reference "IEEE P802.1 Qcr"; } } grouping detnet-node-attributes{ description "DetNet node related attributes."; leaf minimum-packet-processing-delay{ type uint32; description "Minimum packet processing delay in a node. The unit of the delay is microsecond(us)"; } Geng, et al. Expires March 14, 2019 [Page 24] Internet-Draft DetNet Model September 2018 leaf maximum-packet-processing-delay{ type uint32; description "Maximum packet processing delay in a node. The unit of the delay is microsecond(us)"; } leaf maximum-packet-processing-delay-variation{ type uint32; description "Maximum packet processing delay variation in a node. The unit of the delay variation is microsecond(us)"; } } grouping detnet-link-attributes{ description "DetNet link related attributes."; container maximum-reservable-bandwidth{ uses te-types:te-bandwidth; description "This container specifies the maximum bandwidth that is reserved for DetNet on this link."; } container reserved-detnet-bandwidth{ uses te-types:te-bandwidth; description "This container specifies the bandwidth that has been reserved for DetNet on this link."; } container available-detnet-bandwidth{ uses te-types:te-bandwidth; description "This container specifies the bandwidth that is available for new DetNet flows on this link."; } } grouping detnet-terminate-point-attributes{ description "DetNet terminate point related attributes."; leaf elimination-capability{ type boolean; description Geng, et al. Expires March 14, 2019 [Page 25] Internet-Draft DetNet Model September 2018 "Indicates whether a node is able to do packet elimination."; reference "Section 3.2.2.3 of draft-ietf-detnet-architecture"; } leaf replication-capability{ type boolean; description "Indicates whether a node is able to do packet replication."; reference "Section 3.2.2.2 of draft-ietf-detnet-architecture"; } container in-ordering-capability { description "Indicates the parameters needed for packet in-ordering."; reference "Section 3.2.2.1 of draft-ietf-detnet-architecture"; leaf in-ordering-capability { type boolean; description "Indicates whether a node is able to do packet in-ordering."; } leaf maximum-out-of-order-packets { type uint32; description "The maximum number of out-of-order packets."; } } container queuing-algorithm-capabilities { description "All queuing algorithms that a LTP supports."; uses detnet-queuing-algorithms; } list queues { key "queue-identifier"; description "A list of DetNet queues."; leaf queue-identifier { Geng, et al. Expires March 14, 2019 [Page 26] Internet-Draft DetNet Model September 2018 type uint32; description "The identifier of the queue."; } leaf queue-buffer-size { type uint32; description "The size of the queue with unit of bytes."; } container enabled-queuing-algorithm { description "The queuing algorithms that are enabled on the queue."; uses detnet-queuing-algorithms; } leaf minimum-queuing-delay{ type uint32; description "The minimum queuing delay of the queue. The unit of the delay is microsecond(us)"; } leaf maximum-queuing-delay{ type uint32; description "The maximum queuing delay of the queue. The unit of the delay is microsecond(us)"; } leaf maximum-queuing-delay-variation{ type uint32; description "The maximum queuing delay variation of the queue. The unit of the delay variation is microsecond(us)"; } } } augment "/nw:networks/nw:network/nw:network-types/tet:te-topology"{ description "Introduce new network type for TE topology."; container detnet-topology { presence "Indicates DetNet topology."; description "Its presence identifies the DetNet topology type"; } } augment "/nw:networks/nw:network/nw:node/tet:te/" Geng, et al. Expires March 14, 2019 [Page 27] Internet-Draft DetNet Model September 2018 + "tet:te-node-attributes" { when "../../../nw:network-types/tet:te-topology/" + "detnet-topology:detnet-topology" { description "Augmentation parameters apply only for networks with DetNet topology type."; } description "Augmentation parameters apply for DetNet node attributes."; container detnet-node-attributes { description "Attributes for DetNet node."; uses detnet-node-attributes; } } augment "/nw:networks/nw:network/nt:link/tet:te/" + "tet:te-link-attributes" { when "../../../nw:network-types/tet:te-topology/" + "detnet-topology:detnet-topology" { description "Augmentation parameters apply only for networks with DetNet topology type."; } description "Augmentation parameters apply for DetNet link attributes."; container detnet-link-attributes { description "Attributes for DetNet link."; uses detnet-link-attributes; } } augment "/nw:networks/nw:network/nw:node/nt:termination-point/" + "tet:te" { when "../../../nw:network-types/tet:te-topology/" + "detnet-topology:detnet-topology" { description "Augmentation parameters apply only for networks with DetNet topology type."; } description "Augmentation parameters apply for DetNet link termination point."; container detnet-terminate-point-attributes { description "Attributes for DetNet link terminate point."; uses detnet-terminate-point-attributes; Geng, et al. Expires March 14, 2019 [Page 28] Internet-Draft DetNet Model September 2018 } } } //topology module 7.2. DetNet Flow Configuration YANG Model file "ietf-detnet-flow@20180910.yang" module ietf-detnet-flow-config { yang-version 1.1; namespace "urn:ietf:params:xml:ns:yang:ietf-detnet-flow-config"; prefix "detnet-flow"; import ietf-yang-types { prefix "yang"; } import ietf-inet-types{ prefix "inet"; } import ietf-ethertypes { prefix "eth"; } organization "IETF DetNet Working Group"; contact "WG Web: WG List: WG Chair: Lou Berger Janos Farkas Editor: Xuesong Geng Editor: Mach Chen Editor: Zhenqiang Li Editor: Reshad Rahman Geng, et al. Expires March 14, 2019 [Page 29] Internet-Draft DetNet Model September 2018 "; description "This YANG module describes the parameters needed for DetNet flow configuration and flow status reporting."; revision "2018-09-10" { description "initial revision"; reference "RFC XXXX: draft-geng-detnet-config-yang-05"; } identity detnet-node-role { description "base detnet-node-role"; } identity end-station { base detnet-node-role; description "Commonly called a 'host' in IETF documents, and an 'end station' is IEEE 802 documents. End systems of interest to this document are either sources or destinations of DetNet flows. And end system may or may not be DetNet transport layer aware or DetNet service layer aware."; } identity edge-node { base detnet-node-role; description "An instance of a DetNet relay node that includes either a DetNet service layer proxy function for DetNet service protection (e.g. the addition or removal of packet sequencing information) for one or more end systems, or starts or terminate congestion protection at the DetNet transport layer,analogous to a Label Edge Router (LER)."; } identity relay-node { base detnet-node-role; description "A DetNet node including a service layer function that interconnects different DetNet transport layer paths to provide service protection. A DetNet relay node can be a bridge, Geng, et al. Expires March 14, 2019 [Page 30] Internet-Draft DetNet Model September 2018 a router, a firewall, or any other system that participates in the DetNet service layer. It typically incorporates DetNet transport layer functions as well, in which case it is collocated with a transit node."; } identity transit-node { base detnet-node-role; description "A node operating at the DetNet transport layer, that utilizes link layer and/or network layer switching across multiple links and/or sub-networks to provide paths for DetNet service layer functions. Optionally provides congestion protection over those paths. An MPLS LSR is an example of a DetNet transit node."; } identity ttl-action { description "Base identity from which all TTL actions are derived."; } identity no-action { base "ttl-action"; description "Do nothing regarding the TTL."; } identity copy-to-inner { base "ttl-action"; description "Copy the TTL of the outer header to the inner header."; } identity decrease-and-copy-to-inner { base "ttl-action"; description "Decrease TTL by one and copy the TTL to the inner header."; } typedef ttl-action-definition { type identityref { base "ttl-action"; Geng, et al. Expires March 14, 2019 [Page 31] Internet-Draft DetNet Model September 2018 } description "TTL action definition."; } identity detnet-transport-layer { description "The layer that optionally provides congestion protection for DetNet flows over paths provided by the underlying network."; } identity detnet-service-layer { description "The layer at which service protection is provided, either packet sequencing, replication, and elimination or packet encoding"; } typedef service-function-type { type enumeration { enum replication { description "A Packet Replication Function (PRF) replicates DetNet flow packets and forwards them to one or more next hops in the DetNet domain. The number of packet copies sent to each next hop is a DetNet flow specific parameter at the node doing the replication. PRF can be implemented by an edge node, a relay node, or an end system"; } enum elimination { description "A Packet Elimination Function (PEF) eliminates duplicate copies of packets to prevent excess packets flooding the network or duplicate packets being sent out of the DetNet domain. PEF can be implemented by an edge node, a relay node, or an end system."; } enum ordering { description "A Packet Ordering Function (POF) re-orders packets within a DetNet flow that are received out of order. This function can be implemented by an edge node, a relay node, or an end system."; } enum elimination-ordering { Geng, et al. Expires March 14, 2019 [Page 32] Internet-Draft DetNet Model September 2018 description "A combination of PEF and POF that can be implemented by an edge node, a relay node, or an end system."; } enum elimination-replication { description "A combination of PEF and PRF that can be implemented by an edge node, a relay node, or an end system"; } enum elimination-ordering-replicaiton { description "A combination of PEF, POF and PRF that can be implemented by an edge node, a relay node, or an end system"; } } description "DetNet service function and function combination types."; } grouping detnet-transport-qos { description "DetNet transport tunnel QoS attributes."; uses traffic-specification; } grouping ipv4-header { description "The IPv4 header encapsulation information."; leaf src-ipv4-address { type inet:ipv4-address; mandatory true; description "The source IP address of the header."; } leaf dest-ipv4-address { type inet:ipv4-address; mandatory true; description "The destination IP address of the header."; } leaf protocol { type uint8; mandatory true; description Geng, et al. Expires March 14, 2019 [Page 33] Internet-Draft DetNet Model September 2018 "The protocol id of the header."; } leaf ttl { type uint8; description "The TTL of the header."; } leaf dscp { type uint8; description "The DSCP field of the header."; } } grouping ipv6-header { description "The IPv6 header encapsulation information."; leaf src-ipv6-address { type inet:ipv6-address; mandatory true; description "The source IP address of the header."; } leaf dest-ipv6-address { type inet:ipv6-address; mandatory true; description "The destination IP address of the header."; } leaf next-header { type uint8; mandatory true; description "The next header of the IPv6 header."; } leaf traffic-class { type uint8; description "The traffic class value of the header."; } leaf flow-label { type inet:ipv6-flow-label; description "The flow label of the header."; } leaf hop-limit { type uint8 { range "1..255"; Geng, et al. Expires March 14, 2019 [Page 34] Internet-Draft DetNet Model September 2018 } description "The hop limit of the header."; } } grouping mpls-header { description "The MPLS encapsulation header information."; list label-operations { key "label-oper-id"; description "Label operations."; leaf label-oper-id { type uint32; description "An optional identifier that points to a label operation."; } choice label-actions { description "Label action options."; case label-push { container label-push { description "Label push operation."; leaf label { type uint32; mandatory true; description "The label to be pushed."; } leaf s-bit { type boolean; description "The s-bit of the label to be pushed."; } leaf tc-value { type uint8; description "The traffic class value of the label to be pushed."; } leaf ttl-value { type uint8; description "The TTL value of the label to be pushed."; Geng, et al. Expires March 14, 2019 [Page 35] Internet-Draft DetNet Model September 2018 } } } case label-swap { container label-swap { description "Label swap operation."; leaf out-label { type uint32; mandatory true; description "The out MPLS label."; } leaf ttl-action { type ttl-action-definition; description "The label ttl actions: - No-action, or - Copy to inner label,or - Decrease (the in label) by 1 and copy to the out label."; } } } } } } grouping mpls-detnet-header { description "The MPLS DetNet encapsulation header information."; leaf service-label { type uint32; mandatory true; description "The service label."; } leaf control-word { type uint32; mandatory true; description "The control word of the DetNet header."; } } grouping transport-tunnel-encap{ description "Defines the transport tunnel encapsulation Geng, et al. Expires March 14, 2019 [Page 36] Internet-Draft DetNet Model September 2018 header."; choice tunnel-type { description "Tunnel type includes: IPv4, IPv6, MPLS."; case IPv4 { description "IPv4 tunnel."; container ipv4-encapsulation { description "IPv4 encapsulation."; uses ipv4-header; } } case IPv6 { description "IPv6 tunnel."; container ipv6-encapsulation { description "IPv6 encapsulation."; uses ipv6-header; } } case MPLS { description "MPLS tunnel."; container mpls-encapsulation { description "MPLS encapsulation."; uses mpls-header; } } } } grouping detnet-transport-instance { description "An instance of the DetNet transport layer, which depends on the specific data plane that is used as the underlay tunnel."; uses transport-tunnel-encap; uses detnet-transport-qos; } grouping ip-flow-identification { description "IP flow identification."; choice ip-flow-type { description Geng, et al. Expires March 14, 2019 [Page 37] Internet-Draft DetNet Model September 2018 "IP flow types: IPv4, IPv6."; case ipv4 { description "IPv4 flow identification."; leaf src-ipv4-address { type inet:ipv4-address; description "The source IP address of the header."; } leaf dest-ipv4-address { type inet:ipv4-address; description "The destination IP address of the header."; } leaf dscp { type uint8; description "The DSCP field of the header."; } } case ipv6 { description "IPv6 flow identification."; leaf src-ipv6-address { type inet:ipv6-address; description "The source IP address of the header."; } leaf dest-ipv6-address { type inet:ipv6-address; description "The destination IP address of the header."; } leaf traffic-class { type uint8; description "The traffic class value of the header."; } leaf flow-label { type inet:ipv6-flow-label; description "The flow label of the header."; } } } leaf source-port { type inet:port-number; description Geng, et al. Expires March 14, 2019 [Page 38] Internet-Draft DetNet Model September 2018 "The source port number."; } leaf destination-port { type inet:port-number; description "The destination port number."; } leaf protocol { type uint8; description "The protocol id of the header."; } } grouping l3-flow-identification { description "Layer 3 flow identification in the DetNet domain."; choice flow-type { description "L3 DetNet flow types: IP and MPLS."; case IP { description "IP (IPv4 or IPv6) flow identification."; uses ip-flow-identification; } case MPLS { description "MPLS flow identification."; leaf service-label { type uint32; mandatory true; description "The service label."; } } } } //l3-flow-identification grouping in-segments { description "From a receiving node point of view, In-segments are a set of instances of a DetNet flow at the receiving node. This occurs when Packet Replication Function (PRF) is enabled at an upstream node or multiple flows map/aggregate to a single DetNet flow."; list in-segment { Geng, et al. Expires March 14, 2019 [Page 39] Internet-Draft DetNet Model September 2018 key "in-segment-id"; description "A list of in segments, there will be multiple in-segments for a DetNet flow when PRF and PEF enabled."; leaf in-segment-id { type uint32; description "in-segment identifier."; } uses l3-flow-identification; leaf service-function { type service-function-type; description "DetNet service function indication."; } } } grouping out-segments { description "Out-segments are a set of instances of a DetNet flow, this occurs when implement packet replication function, where an in-segment of a DetNet flow is replicated to multiple out-segments."; list out-segment { key "out-segment-id"; description "A list of segments, there will be multiple out-segments when perform PRF."; leaf out-segment-id { type uint32; description "The out-segment identifier"; } container detnet-service-encapsulation { description "Only MPLS based DetNet defines DetNet service layer. The service encapsulation includes service label and control word."; uses mpls-detnet-header; Geng, et al. Expires March 14, 2019 [Page 40] Internet-Draft DetNet Model September 2018 } container detnet-transport-encapsulation { description "Each out-segment corresponds to a transport instance."; uses detnet-transport-instance; } } } grouping detnet-service-instance{ description "An end-2-end DetNet service is consisted of multiple segments. The concept of segment is similar to PW segment. For DetNet, since the existing of PREOF, there could be three cases: 1 - One in-segment maps to multiple out-segments, when implement PRF; 2 - Multiple in-segments map to one out-segment, when implement PEF; 3 - Multiple in-segments map to multiple out-segments, when implement a combination of PEF and PRF."; leaf name { type string; description "The name of the service instance. This MUST be unique across all service instances in a given network device."; } container flow-rank{ description "TBD based on the data plane solution."; } container service-rank{ description "TBD based on the data plane solution."; } uses in-segments; uses out-segments; } grouping l2-flow-identification-at-uni { description "Layer 2 flow identification at UNI."; leaf source-mac-address { Geng, et al. Expires March 14, 2019 [Page 41] Internet-Draft DetNet Model September 2018 type yang:mac-address; description "The source MAC address used for flow identification."; } leaf destination-mac-address { type yang:mac-address; description "The destination MAC address used for flow identification."; } leaf ethertype { type eth:ethertype; description "The Ethernet Type (or Length) value represented in the canonical order defined by IEEE 802. The canonical representation uses lowercase characters."; reference "IEEE 802-2014 Clause 9.2"; } leaf vlan-id { type uint16 { range "1..4094"; } description "Vlan Identifier used for L2 flow identification."; } container pcp { //Todo description "PCP used for L2 flow identification."; } } grouping l3-flow-identification-at-uni { description "Layer 3 flow identification at UNI."; uses ip-flow-identification; } grouping traffic-specification { description "traffic-specification specifies how the Source transmits packets for the flow. This is the promise/request of the Source to the network. Geng, et al. Expires March 14, 2019 [Page 42] Internet-Draft DetNet Model September 2018 The network uses this traffic specification to allocate resources and adjust queue parameters in network nodes."; reference "draft-ietf-detnet-flow-information-model"; leaf interval { type uint32; description "The period of time in which the traffic specification cannot be exceeded"; } leaf max-packets-per-interval{ type uint32; description "The maximum number of packets that the source will transmit in one Interval."; } leaf max-payload-size{ type uint32; description "The maximum payload size that the source will transmit."; } leaf average-packets-per-interval { type uint32; description "The average number of packets that the source will transmit in one Interval"; } leaf average-payload-size { type uint32; description "The average payload size that the source will transmit."; } } grouping client-flows-at-uni { description "The attributes of the client flow at UNI. When flow aggregation is enabled at ingress, multiple client flows map to a DetNet service instance."; list client-flow { key "flow-id"; description "A list of client flows."; leaf flow-id { Geng, et al. Expires March 14, 2019 [Page 43] Internet-Draft DetNet Model September 2018 type uint32; description "Flow identifier that is unique in a network device for client flow identification"; } choice flow-type{ description "Client flow type: layer 2 flow, layer 3 flow."; case l2-flow-identfication { description "Ethernet flow identification."; uses l2-flow-identification-at-uni; } case l3-flow-identification { description "layer 3 flow identification, including IPv4,IPv6 and MPLS."; uses l3-flow-identification-at-uni; } } container traffic-specification { description "The traffic specification of the client flow."; uses traffic-specification; } } } grouping detnet-service-proxy-instance { description "Maps between App-flows and DetNet flows"; uses client-flows-at-uni; container detnet-service-instance { description "A DetNet service instance."; uses detnet-service-instance; } } container detnet-flow{ description "DetNet flow configuration and status reporting."; choice detnet-node-role{ description "Depends on the role of a node to configure corresponding flow parameters."; Geng, et al. Expires March 14, 2019 [Page 44] Internet-Draft DetNet Model September 2018 case transit-node{ description "DetNet flow configuration parameters for transit nodes."; container transit-node { description "transit node container."; uses detnet-transport-qos; } } case relay-node{ description "DetNet flow configuration parameters for relay nodes."; container relay-node { description "Relay node container."; uses detnet-service-instance; } } case edge-node{ description "DetNet flow configuration parameters for edge nodes."; container edge-node { description "Edge node container."; uses detnet-service-proxy-instance; } } case end-station { description "DetNet flow configuration parameters for end stations."; container end-station { description "End station container."; uses detnet-service-proxy-instance; } } } } } Geng, et al. Expires March 14, 2019 [Page 45] Internet-Draft DetNet Model September 2018 8. DetNet Configuration Model Classification This section defines three classes of DetNet configuration model: fully distributed configuration model, fully centralized configuration model, hybrid configuration model, based on different network architectures, showing how configuration information exchanges between various entities in the network. 8.1. Fully Distributed Configuration Model In a fully distributed configuration model, UNI information is transmitted over DetNet UNI protocol from the user side to the network side; then UNI information and network configuration information propagate in the network over distributed control plane protocol. For example: 1) IGP collects topology information and DetNet capabilities of network([I-D.geng-detnet-info-distribution]); 2) Control Plane of the Edge Node(Ingress) receives a flow establishment request from UNI and calculates a/some valid path(s); 3) Using RSVP-TE, Edge Node(Ingress) sends a PATH message with explicit route. After receiving the PATH message, the other Edge Node(Egress) sends a Resv message with distributed label and resource reservation request. Current distributed control plane protocol,e.g., RSVP-TE[RFC3209], SRP[IEEE802.1Qcc], can only reserve bandwidth along the path, while the configuration of a fine-grained schedule, e.g.,Time Aware Shaping(TAS) defined in [IEEE802.1Qbv], is not supported. The fully distributed configuration model is not covered by this draft. It should be discussed in the future DetNet control plane work. 8.2. Fully Centralized Configuration Model In the fully centralized configuration model, UNI information is transmitted from Centralized User Configuration (CUC) to Centralized Network Configuration(CNC). Configurations of routers for DetNet flows are performed by CNC with network management protocol. For example: 1) CNC collects topology information and DetNet capability of network through Netconf; Geng, et al. Expires March 14, 2019 [Page 46] Internet-Draft DetNet Model September 2018 2) CNC receives a flow establishment request from UNI and calculates a/some valid path(s); 3) CNC configures the devices along the path for flow transmission. 8.3. Hybrid Configuration Model In the hybrid configuration model, controller and control plane protocols work together to offer DetNet service, and there are a lot of possible combinations. For example: 1) CNC collects topology information and DetNet capability of network through IGP/BGP-LS; 2) CNC receives a flow establishment request from UNI and calculates a/some valid path(s); 3) Based on the calculation result, CNC distributes flow path information to Edge Node(Ingress) and other information(e.g. replication/elimination) to the relevant nodes. 4) Using RSVP-TE, Edge Node(Ingress) sends a PATH message with explicit route. After receiving the PATH message, the other Edge Node(Egress) sends a Resv message with distributed label and resource reservation request. or 1) Controller collects topology information and DetNet capability of network through IGP/BGP-LS; 2) Control Plane of Edge Node(Ingress) receives a flow establishment request from UNI; 3) Edge Node(Ingress) sends the path establishment request to CNC through PCEP; 4) After Calculation, CNC sends back the path information of the flow to the Edge Node(Ingress) through PCEP; 5) Using RSVP-TE, Edge Node(Ingress) sends a PATH message with explicit route. After receiving the PATH message, the other Edge Node(Egress) sends a Resv message with distributed label and resource reservation request. There are also other variations that can be included in the hybrid model. This draft can not coverer all the control plane data needed Geng, et al. Expires March 14, 2019 [Page 47] Internet-Draft DetNet Model September 2018 in hybrid configuration models. Every solution has there own mechanism and corresponding parameters to make it work. Editor's Note: 1. There are a lot of optional DetNet configuration models, and different scenario in different use case can choose one of them based on its conditions. Maybe next step of the work is to pick up one or more typical scenarios and give a practical solution. 2. [IEEE802.1Qcc] also defines three TSN configuration models: fully-centralized model, fully-distributed model, centralized Network / distributed User Model. This section defines the configuration model roughly the same, to keep the design of L2 and L3 in the same structure. Hybrid configuration model is slightly different from the 'centralized Network / distributed User Model'. The hybrid configuration model intends to contain more variations. 9. IANA Considerations This document makes no request of IANA. Note to RFC Editor: this section may be removed on publication as an RFC. 10. Security Considerations 11. Acknowledgements 12. References 12.1. Normative References [I-D.finn-detnet-bounded-latency] Finn, N., Boudec, J., Mohammadpour, E., Varga, B., and J. Farkas, "DetNet Bounded Latency", draft-finn-detnet- bounded-latency-01 (work in progress), July 2018. [I-D.ietf-detnet-architecture] Finn, N., Thubert, P., Varga, B., and J. Farkas, "Deterministic Networking Architecture", draft-ietf- detnet-architecture-07 (work in progress), August 2018. Geng, et al. Expires March 14, 2019 [Page 48] Internet-Draft DetNet Model September 2018 [I-D.ietf-detnet-dp-sol-ip] Korhonen, J. and B. Varga, "DetNet IP Data Plane Encapsulation", draft-ietf-detnet-dp-sol-ip-00 (work in progress), July 2018. [I-D.ietf-detnet-dp-sol-mpls] Korhonen, J. and B. Varga, "DetNet MPLS Data Plane Encapsulation", draft-ietf-detnet-dp-sol-mpls-00 (work in progress), July 2018. [I-D.ietf-detnet-flow-information-model] Farkas, J., Varga, B., rodney.cummings@ni.com, r., Jiang, Y., and Y. Zha, "DetNet Flow Information Model", draft- ietf-detnet-flow-information-model-01 (work in progress), March 2018. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, July 2013, . [RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, August 2016, . 12.2. Informative References [I-D.geng-detnet-info-distribution] Geng, X., Chen, M., and Z. Li, "IGP-TE Extensions for DetNet Information Distribution", draft-geng-detnet-info- distribution-02 (work in progress), March 2018. [I-D.ietf-detnet-use-cases] Grossman, E., "Deterministic Networking Use Cases", draft- ietf-detnet-use-cases-17 (work in progress), June 2018. [I-D.ietf-teas-yang-te] Saad, T., Gandhi, R., Liu, X., Beeram, V., Shah, H., and I. Bryskin, "A YANG Data Model for Traffic Engineering Tunnels and Interfaces", draft-ietf-teas-yang-te-16 (work in progress), July 2018. Geng, et al. Expires March 14, 2019 [Page 49] Internet-Draft DetNet Model September 2018 [I-D.ietf-teas-yang-te-topo] Liu, X., Bryskin, I., Beeram, V., Saad, T., Shah, H., and O. Dios, "YANG Data Model for Traffic Engineering (TE) Topologies", draft-ietf-teas-yang-te-topo-18 (work in progress), June 2018. [I-D.thubert-tsvwg-detnet-transport] Thubert, P., "A Transport Layer for Deterministic Networks", draft-thubert-tsvwg-detnet-transport-01 (work in progress), October 2017. [I-D.varga-detnet-service-model] Varga, B. and J. Farkas, "DetNet Service Model", draft- varga-detnet-service-model-02 (work in progress), May 2017. [IEEE802.1CB] "IEEE, "Frame Replication and Elimination for Reliability (IEEE Draft P802.1CB)", 2017, .", 2016. [IEEE802.1Q-2014] "IEEE, "IEEE Std 802.1Q Bridges and Bridged Networks", 2014, .", 2014. [IEEE802.1Qbu] "IEEE, "IEEE Std 802.1Qbu Bridges and Bridged Networks - Amendment 26: Frame Preemption", 2016, .", 2016. [IEEE802.1Qbv] "IEEE, "IEEE Std 802.1Qbu Bridges and Bridged Networks - Amendment 25: Enhancements for Scheduled Traffic", 2015, .", 2016. [IEEE802.1Qcc] "IEEE, "Stream Reservation Protocol (SRP) Enhancements and Performance Improvements (IEEE Draft P802.1Qcc)", 2017, .". [IEEE802.1Qch] "IEEE, "Cyclic Queuing and Forwarding (IEEE Draft P802.1Qch)", 2017, .", 2016. Geng, et al. Expires March 14, 2019 [Page 50] Internet-Draft DetNet Model September 2018 [IEEE802.1Qci] "IEEE, "Per-Stream Filtering and Policing (IEEE Draft P802.1Qci)", 2016, .", 2016. [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001, . [RFC4875] Aggarwal, R., Ed., Papadimitriou, D., Ed., and S. Yasukawa, Ed., "Extensions to Resource Reservation Protocol - Traffic Engineering (RSVP-TE) for Point-to- Multipoint TE Label Switched Paths (LSPs)", RFC 4875, DOI 10.17487/RFC4875, May 2007, . [RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018, . Authors' Addresses Xuesong Geng Huawei Email: gengxuesong@huawei.com Mach(Guoyi) Chen Huawei Email: mach.chen@huawei.com Zhenqiang Li China Mobile Email: lizhenqiang@chinamobile.com Reshad Rahman Cisco Systems Email: rrahman@cisco.com Geng, et al. Expires March 14, 2019 [Page 51]