Network Working Group J. Arkko Internet-Draft Ericsson Intended status: Standards Track F. Baker Expires: August 29, 2010 Cisco Systems February 25, 2010 Guidelines for Using IPv6 Transition Mechanisms draft-arkko-ipv6-transition-guidelines-01 Abstract The Internet continues to grow beyond the capabilities of IPv4. An expansion in the address space is clearly required. With its increase in the number of available prefixes and addresses in a subnet, and improvements in address management, IPv6 is the only real option on the table. Yet, IPv6 deployment requires some effort, resources, and expertise. The availability of many different deployment models is one reason why expertise is required. This document discusses the IPv6 deployment models and migration tools, and recommends ones that have been found to work well in many common situations. Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on August 29, 2010. Copyright Notice Arkko & Baker Expires August 29, 2010 [Page 1] Internet-Draft IPv6 Transition Guidelines February 2010 Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Principles . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3.1. Goals . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3.2. Choosing a Deployment Model . . . . . . . . . . . . . . . 5 4. Guidelines for IPv6 Deployment . . . . . . . . . . . . . . . . 7 4.1. Native Dual Stack . . . . . . . . . . . . . . . . . . . . 7 4.2. Crossing IPv4 Islands . . . . . . . . . . . . . . . . . . 9 4.3. IPv6-Only Core Network . . . . . . . . . . . . . . . . . . 9 4.4. Unilateral Deployment . . . . . . . . . . . . . . . . . . 10 5. Further Reading . . . . . . . . . . . . . . . . . . . . . . . 11 6. Security Considerations . . . . . . . . . . . . . . . . . . . 11 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 11 8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 12 8.1. Normative References . . . . . . . . . . . . . . . . . . . 12 8.2. Informative References . . . . . . . . . . . . . . . . . . 12 Appendix A. Acknowledgments . . . . . . . . . . . . . . . . . . . 15 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 15 Arkko & Baker Expires August 29, 2010 [Page 2] Internet-Draft IPv6 Transition Guidelines February 2010 1. Introduction The Internet continues to grow beyond the capabilities of IPv4. The tremendous success of the Internet has strained the IPv4 address space, which is no longer sufficient to fuel future growth. At the time of this writing, the IANA "free pool" contained only 24 unallocated unicast IPv4 /8 prefixes. This is sufficient for the next 2-3 years at best. An expansion in the address space is clearly required. With its increase in the number of available prefixes and addresses in a subnet, and improvements in address management, IPv6 is the only real option on the table. Accordingly, many organizations have employed or are planning to employ IPv6 in their networks. Yet, IPv6 deployment requires some effort, resources, and expertise. This is largely a natural part of maintaining and evolving a network: changing requirements are taken into account in normal planning, procurement and update cycles. Very large networks have successfully adopted IPv6 alongside IPv4, with surprisingly little effort. However, in order to successfully make this transition, some amount of new expertise is required. Different types of experience will be required: basic understanding of IPv6 mechanisms, debugging tools, product capabilities and caveats when used with IPv6, and so on. The availability of many different IPv6 deployment models and tools is an additional reason why expertise is required. These models and tools have been developed over the years at the IETF, some for specific circumstances and others for more general use. They differ greatly in their principles of operation. Over time, views about the best ways to employ the tools have evolved. Given the number of options, network managers are understandably confused. They need guidance on recommended approaches to IPv6 deployment. The rest of this document is organized as follows. Section 2 introduces some terminology, Section 3 discusses some of the general principles behind choosing particular deployment models and tools, and Section 4 goes through the recommended deployment models for common situations 2. Terminology In this document, the following terms are used. "NAT44" refers to any IPv4-to-IPv4 network address translation algorithm, both "Basic NAT" and "Network Address/Port Translator (NAPT)", as defined by [RFC2663]. "Dual Stack" refers to a technique for providing complete support for Arkko & Baker Expires August 29, 2010 [Page 3] Internet-Draft IPv6 Transition Guidelines February 2010 both Internet protocols -- IPv4 and IPv6 -- in hosts and routers [RFC4213]. "Dual Stack Lite" refers to a technique that employs tunneling and NAT44 to provide IPv4 connectivity over IPv6 networks [I-D.ietf-softwire-dual-stack-lite]. "NAT-PT" refers to a specific, old design of a Network Address Translator - Protocol Translator defined in [RFC2766]. 3. Principles The end goal is network-wide native IPv6 deployment, resulting in the obsolescence of transitional mechanisms based on encapsulation, tunnels, or translation, and also resulting in the obsolescence of IPv4. Transition mechanisms, taken as a class, are a means to an end, to simplify the process for the network administration. However, the goals, constraints, and opportunities for IPv6 deployment differ from one case to another. There is no single right model for IPv6 deployment, just like there is no one and only model IPv4 network design. Some guidelines can be given, however. Common deployment models that have been found to work well are discussed in Section 4, and the small set of standardized IETF migration tools support these models. But first it may be useful to discuss some general principles that guide our thinking about what is a good deployment model. 3.1. Goals The primary goal is to facilitate the continued growth of the networking industry and deployment of Internet technology at relatively low capital and operational expense. This is at risk with IPv4 due to the address runout; economics teaches us that a finite resource, when stressed, becomes expensive, either in the actual cost of the resource or in the complexity of the technology and processes required to manage it. It is also at risk while both IPv4 and IPv6 are deployed in parallel, as it costs more to run two technologies than one. To this end, since IPv4 clearly will not scale to meet our insatiable requirements, the primary technical goals are the global deployment of IPv6 both in the network and by applications, and the resulting obsolescence of IPv4. Temporary goals in support of this focus on enabling parts of the Internet to employ IPv6 and disable IPv4 before the entire Internet has done so. It is important to start the deployment process in a timely manner. Most of the effort is practical -- network component choices, network Arkko & Baker Expires August 29, 2010 [Page 4] Internet-Draft IPv6 Transition Guidelines February 2010 management, planning, implementation -- and at the time of this writing, reasonably easily achievable. There is no particular advantage to avoiding dealing with IPv6 as a part the normal network planning cycle. The migration tools already exist, and while additional features continue to be developed it is not expected that they radically change what networks have to do. In other words, there is no point in waiting for an improved design. There are only a few exceptional networks where co-existence with IPv4 is not a consideration at all. These networks are typically new deployments, strictly controlled by a central authority, and have no need to deal with legacy devices. For example, specialized sensor networks that communicate only to designated servers can easily be deployed as IPv6-only networks. In most other networks IPv4 has to be considered. A typical requirement is that older, IPv4-only devices must be accommodated. Most networks that cross administrative boundaries or allow end user equipment have such requirements. Even in situations where the network consists of only new, IPv6-capable devices it is typically required that the devices can communicate with the IPv4 Internet. It is expected that after a period of supporting both IPv4 and IPv6, IPv4 can eventually be turned off. This should happen gradually. For instance, a service provider network might stop providing IPv4 service within its own network, while still allowing its IPv6 customers to access the rest of the IPv4 Internet. 3.2. Choosing a Deployment Model The first requirement is that the model or tool actually allows communications to flow. While this sounds too obvious to even state, it is sometimes not easy to ensure that a proposed model does not have failure modes related to supporting older devices, for instance. A network that is not serving all of its users is not fulfilling its task. The ability to communicate is also far more important than fine- grained performance differences. In general, it is not productive to focus on optimization of a design that is designed to be temporary, such as a migration solution necessarily is. Consequently, existing tools are often preferred over new ones, even if for some specific circumstance it would be possible to construct a slightly more efficient design. Similarly, migration tools that can be disposed after a period of co- existence are preferred over tools that require more permanent changes. Such permanent changes may incur costs even after the transition to IPv6 has been completed. Arkko & Baker Expires August 29, 2010 [Page 5] Internet-Draft IPv6 Transition Guidelines February 2010 Looking back on the deployment of Internet technology, some of the factors that have been important for success include [RFC5218, baker.shanghai] o The ability to offer a valuable service. In the case of the Internet, connectivity has been this service. o The ability to deploy the solution in an incremental fashion. o Simplicity. This has been a key factor in making it possible for all types of devices to support the Internet protocols. o Openly available implementations. These make it easier for researchers, start-ups and others to build on or improve existing components. o The ability to scale. The IPv4 Internet grew far larger than its original designers had anticipated, and scaling limits only became apparent 20-30 years later. o The design supports robust interoperability rather than mere correctness. This is important in order to ensure that the solution works in different circumstances and in an imperfectly controlled world. These factors are also important when choosing IPv6 migration tools. It is also essential that any chosen designs allow the network to be maintained, serviced, diagnosed and measured. The ability of the network to operate under many different circumstances and surprising conditions is a key. Any large network that employs brittle components will incur significant support costs. For instance, it is generally a bad assumption that large number of devices have specific software or configuration. Properly executed IPv6 deployment normally involves a step-wise approach where individual functions or parts of the network are updated at different times. For instance, IPv6 connectivity has to be established and tested before DNS entries with IPv6 addresses can be entered. Or specific services can be moved to support IPv6 earlier than others. In general, most deployment models employ a very similar network architecture for both IPv4 and IPv6. The principle of changing only the minimum amount necessary is applied here. Arkko & Baker Expires August 29, 2010 [Page 6] Internet-Draft IPv6 Transition Guidelines February 2010 4. Guidelines for IPv6 Deployment This section presents a number of common scenarios along with recommended deployment tools for them. We start from the default, simplest deployment situation where native connectivity is available and both IP versions are used. Since native IPv6 connectivity not available in all networks, our second scenario looks at ways of arranging such connectivity over the IPv4 Internet. The third scenario is more advanced and looks at a service provider network that runs only on IPv6 but which is still capable of providing both IPv6 and IPv4 services. The fourth and most advanced scenario focuses unilateral deployment of IPv6, i.e., being able to employ IPv6 for a particular communication flow even if the other end is still on IPv4. Note that there are many other possible deployment models and existing specifications to support such models. These other models are not necessarily frowned upon. However, they are not expected to be the mainstream deployment models, and consequently, the associated specifications are typically not IETF standards track RFCs. Network managers should not adopt these non-mainstream models lightly, however, as there is little guarantee that they work well. There are also models that are believed to be problematic. An older model to IPv6 - IPv4 translation (NAT-PT) [RFC2766] suffers from a number of drawbacks arising from, for example, its attempt to capture DNS queries on path [RFC4966]. Another example regarding the preference to employ tunneling instead of double translation will be discussed later in this document. 4.1. Native Dual Stack The simplest deployment model is Dual Stack: one turns on IPv6 throughout one's existing IPv4 network and allows applications using the two protocols to operate as ships in the night. This model is applicable to most networks - home, enterprise, service provider, or content provider network. The purpose of this model is to support any type of device and communication, and to make it an end-to-end choice which IP version is used between the peers. There are minimal assumptions about the capabilities and configuration of hosts in these networks. Native connectivity avoids problems associated with the configuration of tunnels and Maximum Transfer Unit (MTU) settings. As a result, these networks are robust and reliable. Accordingly, this is the recommended deployment model for most networks, and supported by IETF standards such as dual stack [RFC4213] and address selection [RFC3484]. Arkko & Baker Expires August 29, 2010 [Page 7] Internet-Draft IPv6 Transition Guidelines February 2010 The challenges associated with this model are two-fold. First, while dual-stack allows each individual network to deploy IPv6 on their own, actual use still requires participation from all parties between the peers. For instance, the peer must be reachable over IPv6, have an IPv6 address to itself, and advertise such an address in the relevant naming service (such as the DNS). This can create a situation where IPv6 has been turned on in a network but there is little actual traffic. One direct way to affect this situation is to ensure that major destinations of traffic are prepared to receive IPv6 traffic. Current Internet traffic is highly concentrated on selected content provider networks, and making a change in even a small number of these networks can have significant effects. This was recently observed when YouTube started supporting IPv6 [networkworld.youtube]. The second challenge is that not all applications deal gracefully with situations where one of the alternative destination addresses works unreliably. For instance, if IPv6 connectivity is unreliable it may take a long time for some applications to switch over to IPv4. As a result, many content providers are shying away from advertising IPv6 addresses in DNS. This in turn exacerbates the first challenge. Long term, the use of modern application toolkits and APIs solves this problem. In the short term content providers and user network managers have made a mutual agreement a requirement to resolve names to IPv6 addresses. Such agreements are similar to peering agreements and are necessary for the time being. Nevertheless, there are many types of traffic in the Internet and only some of it requires such careful coordination. Popular peer-to-peer systems can automatically and reliably employ IPv6 connectivity where it is available, for instance. Despite these challenges the native dual stack connectivity model remains the recommended approach. It is responsible for a large part of the forward progress on world-wide IPv6 deployment. The largest IPv6 networks employ this approach. The original intent of dual stack was to deploy both IP versions alongside each other before IPv4 addresses were to run out. As we know, this never happened and deployment now has to take place with limited IPv4 addresses. Employing dual stack together with a traditional IPv4 address translator (NAT44) is a very common configuration. If the address translator is acceptable for the network from a pure IPv4 perspective, this model can be recommended from a dual stack perspective as well. The advantage of IPv6 in this model is that it allows direct addressing of specific nodes in the network, creating a contrast to the translated IPv4 service and allowing the construction of IPv6-based applications that offer more functionality. Arkko & Baker Expires August 29, 2010 [Page 8] Internet-Draft IPv6 Transition Guidelines February 2010 There may also be situations where a traditional IPv4 address translator is no longer sufficient. For instance, in typical residential networks, each subscriber is given one global IPv4 address, and the subscriber's NAT44 device may use this address with as many devices as it can handle. As IPv4 address space becomes more constrained and without substantial movement to IPv6, it is expected that service providers will be pressured to assign a single global IPv4 address to multiple subscribers. Indeed, in some deployments this is already the case. The dual stack model is still applicable even in these networks, but the NAT44 functionality may need to be relocated and enhanced. On some networks it is possible to employ overlapping private address space [I-D.miles-behave-l2nat] [I-D.arkko-dual-stack-extra-lite]. Other networks may require a combination of NAT44 enhancements and tunneling. These scenarios are discussed further in Section 4.3. 4.2. Crossing IPv4 Islands Native IPv6 connectivity is not always available, but fortunately it can established using tunnels. Tunneling introduces some additional complexity and has a risk of MTU or other mis-configurations. It should only be used when establishing native connectivity is not possible. Typically, this involves crossing another administrative domain or a router that cannot be easily re-configured. There are several types tunneling mechanisms, including manually configured IPv6-over-IPv4 tunnels [RFC4213], automatic host-based tunnels [RFC4380] and the use of Virtual Private Network (VPN) or mobility tunnels to carry both IPv4 and IPv6 [RFC4301] [RFC5454] [RFC5555]. More advanced solutions provide a mesh-based framework of tunnels [RFC5565]. There are no major challenges with tunneling beyond the possible configuration and MTU problems. Tunneling is very widely deployed both for IPv6 connectivity and other reasons, and well understood. In general, the IETF recommends that tunneling be used if it is necessary to cross a segment of IP version X when communicating from IP version Y to Y. An alternative design would be to employ protocol translation twice. However, this design involves problems similar to those created by IPv4 address translation and is largely untried technology in any larger scale. 4.3. IPv6-Only Core Network An emerging deployment model uses IPv6 as the dominant protocol at a service provider network, and tunnels IPv4 through this network in a manner similar to the one described in the previous section. There are several motivations for choosing this deployment model: Arkko & Baker Expires August 29, 2010 [Page 9] Internet-Draft IPv6 Transition Guidelines February 2010 o There may not be enough public or private addresses to support network management functions in an end-to-end fashion, without segmenting the network into small parts with overlapping address space. o IP address sharing among subscribers may involve new address translation nodes within the service provider's network. IPv6 can be used to reach these nodes. Normal IPv4 routing is insufficient for this purpose, as the same addresses would be used in several parts of the network. o It may be simpler for the service provider to employ a single- version network. The recommended tool for this model is Dual Stack Lite [I-D.ietf-softwire-dual-stack-lite]. Dual Stack Lite provides both relief for IPv4 address shortage and makes forward progress on IPv6 deployment, by moving service provider networks and IPv4 traffic over IPv6. Given this IPv6 connectivity, as a side-effect it becomes easy to provide IPv6 connectivity all the way to the end users. 4.4. Unilateral Deployment Our final deployment model breaks the requirement that all parties must upgrade to IPv6 before any actual communications use IPv6. This model makes sense when the following conditions are met: o There is a fact or requirement that there be an IPv4-only domain and an IPv6-only domain. o There is a requirement that hosts in the IPv4-only domain access servers or peers in the IPv6-only domain and vice versa. When we say "IPv4-only" or "IPv6-only", we mean that the applications can communicate only using IPv4 or IPv6; this might be due to the absence of stacks in the hosts or routing in the network; the effect is the same. The reason to switch to an IPv6-only network may be a desire to test such a configuration, or to simplify the network. It is expected that as IPv6 deployment progresses, the second reason will become more prevalent. One particular reason for considering an IPv6-only domain is the effect of overlapping private address space to applications. This is important in networks that have exhausted both public and private IPv4 address space and where arranging an IPv6-only network is easier than dealing with the overlapping address space in applications. Note that the existence of an IPv6-only domain requires that all devices are indeed IPv6-capable. In today's mixed networking Arkko & Baker Expires August 29, 2010 [Page 10] Internet-Draft IPv6 Transition Guidelines February 2010 environments with legacy devices this can not always be guaranteed. But it can be arranged in networks where all devices are controlled by a central authority. For instance, newly built corporate networks. One obvious unilateral deployment approach applies to applications that include proxies or relays. One might position a web proxy, a mail server, or a voice transcoder across the boundary between IPv4 and IPv6 domains, so that the application terminates IPv4 sessions on one side and IPv6 sessions on the other. Doing this preserves the end-to-end nature of communications between gateways. For obvious reasons, this solution is preferable to the implementation of Application Layer Gateways in network layer translators. The other approach is network layer IPv4/IPv6 translation as described in IPv4/IPv6 Translation [I-D.ietf-behave-v6v4-framework] [I-D.ietf-behave-v6v4-xlate] [I-D.ietf-behave-v6v4-xlate-stateful] [I-D.ietf-behave-address-format] [I-D.ietf-behave-dns64] [I-D.ietf-behave-ftp64]. IPv4/IPv6 translation at the network layer is similar in its advantages and pitfalls to IPv4/IPv4 translation. It is, however, stateless for interfaces in the IPv6-only network with IPv4-mapped addresses, and allows IPv4 hosts to directly initiate communication with those interfaces. 5. Further Reading Various aspects of IPv6 deployment have been covered in several RFCs. Of particular interest may be the basic dual stack definition [RFC4213], application aspects [RFC4038], deployment in Internet Service Provider Networks [RFC4029], deployment in enterprise networks [RFC4057] [RFC4852], and considerations in specific access networks such as cellular networks [RFC3314] [RFC3574] [RFC4215] or 802.16 networks [RFC5181]. 6. Security Considerations This document has no impact on the security properties of specific IPv6 transition tools. 7. IANA Considerations This document has no IANA implications. 8. References Arkko & Baker Expires August 29, 2010 [Page 11] Internet-Draft IPv6 Transition Guidelines February 2010 8.1. Normative References [RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address Translator (NAT) Terminology and Considerations", RFC 2663, August 1999. [RFC3484] Draves, R., "Default Address Selection for Internet Protocol version 6 (IPv6)", RFC 3484, February 2003. [RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms for IPv6 Hosts and Routers", RFC 4213, October 2005. [RFC4301] Kent, S. and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, December 2005. [RFC4380] Huitema, C., "Teredo: Tunneling IPv6 over UDP through Network Address Translations (NATs)", RFC 4380, February 2006. [RFC5454] Tsirtsis, G., Park, V., and H. Soliman, "Dual-Stack Mobile IPv4", RFC 5454, March 2009. [RFC5555] Soliman, H., "Mobile IPv6 Support for Dual Stack Hosts and Routers", RFC 5555, June 2009. [RFC5565] Wu, J., Cui, Y., Metz, C., and E. Rosen, "Softwire Mesh Framework", RFC 5565, June 2009. 8.2. Informative References [RFC2766] Tsirtsis, G. and P. Srisuresh, "Network Address Translation - Protocol Translation (NAT-PT)", RFC 2766, February 2000. [RFC3314] Wasserman, M., "Recommendations for IPv6 in Third Generation Partnership Project (3GPP) Standards", RFC 3314, September 2002. [RFC3574] Soininen, J., "Transition Scenarios for 3GPP Networks", RFC 3574, August 2003. [RFC4029] Lind, M., Ksinant, V., Park, S., Baudot, A., and P. Savola, "Scenarios and Analysis for Introducing IPv6 into ISP Networks", RFC 4029, March 2005. [RFC4038] Shin, M-K., Hong, Y-G., Hagino, J., Savola, P., and E. Castro, "Application Aspects of IPv6 Transition", RFC 4038, March 2005. Arkko & Baker Expires August 29, 2010 [Page 12] Internet-Draft IPv6 Transition Guidelines February 2010 [RFC4057] Bound, J., "IPv6 Enterprise Network Scenarios", RFC 4057, June 2005. [RFC4215] Wiljakka, J., "Analysis on IPv6 Transition in Third Generation Partnership Project (3GPP) Networks", RFC 4215, October 2005. [RFC4852] Bound, J., Pouffary, Y., Klynsma, S., Chown, T., and D. Green, "IPv6 Enterprise Network Analysis - IP Layer 3 Focus", RFC 4852, April 2007. [RFC4966] Aoun, C. and E. Davies, "Reasons to Move the Network Address Translator - Protocol Translator (NAT-PT) to Historic Status", RFC 4966, July 2007. [RFC5181] Shin, M-K., Han, Y-H., Kim, S-E., and D. Premec, "IPv6 Deployment Scenarios in 802.16 Networks", RFC 5181, May 2008. [RFC5218] Thaler, D. and B. Aboba, "What Makes For a Successful Protocol?", RFC 5218, July 2008. [I-D.ietf-softwire-dual-stack-lite] Durand, A., Droms, R., Haberman, B., Woodyatt, J., Lee, Y., and R. Bush, "Dual-stack lite broadband deployments post IPv4 exhaustion", draft-ietf-softwire-dual-stack-lite-03 (work in progress), February 2010. [I-D.ietf-behave-v6v4-framework] Baker, F., Li, X., Bao, C., and K. Yin, "Framework for IPv4/IPv6 Translation", draft-ietf-behave-v6v4-framework-06 (work in progress), February 2010. [I-D.ietf-behave-address-format] Huitema, C., Bao, C., Bagnulo, M., Boucadair, M., and X. Li, "IPv6 Addressing of IPv4/IPv6 Translators", draft-ietf-behave-address-format-04 (work in progress), January 2010. [I-D.ietf-behave-dns64] Bagnulo, M., Sullivan, A., Matthews, P., and I. Beijnum, "DNS64: DNS extensions for Network Address Translation from IPv6 Clients to IPv4 Servers", draft-ietf-behave-dns64-06 (work in progress), February 2010. Arkko & Baker Expires August 29, 2010 [Page 13] Internet-Draft IPv6 Transition Guidelines February 2010 [I-D.ietf-behave-v6v4-xlate] Li, X., Bao, C., and F. Baker, "IP/ICMP Translation Algorithm", draft-ietf-behave-v6v4-xlate-09 (work in progress), February 2010. [I-D.ietf-behave-v6v4-xlate-stateful] Bagnulo, M., Matthews, P., and I. Beijnum, "Stateful NAT64: Network Address and Protocol Translation from IPv6 Clients to IPv4 Servers", draft-ietf-behave-v6v4-xlate-stateful-08 (work in progress), January 2010. [I-D.ietf-behave-ftp64] Beijnum, I., "IPv6-to-IPv4 translation FTP considerations", draft-ietf-behave-ftp64-00 (work in progress), December 2009. [I-D.arkko-townsley-coexistence] Arkko, J. and M. Townsley, "IPv4 Run-Out and IPv4-IPv6 Co- Existence Scenarios", draft-arkko-townsley-coexistence-03 (work in progress), July 2009. [I-D.miles-behave-l2nat] Miles, D. and M. Townsley, "Layer2-Aware NAT", draft-miles-behave-l2nat-00 (work in progress), March 2009. [I-D.arkko-dual-stack-extra-lite] Arkko, J. and L. Eggert, "Scalable Operation of Address Translators with Per-Interface Bindings", draft-arkko-dual-stack-extra-lite-00 (work in progress), February 2010. [baker.shanghai] Baker, F., "The view from IPv6 Operations WG (and we'll talk about translation)", Presentation in the China Mobile Workshop on IPv6 Deployment in Cellular Networks, http:// ipv6ws.arkko.com/presentations/ 3GPP-IETF-V6OPS-Discussion.pdf, Shanghai, China, November 2009. [networkworld.youtube] Marsan, C., "YouTube support of IPv6 seen in dramatic traffic spike", Network World article http:// www.networkworld.com/news/2010/020110-youtube-ipv6.html, February 2010. Arkko & Baker Expires August 29, 2010 [Page 14] Internet-Draft IPv6 Transition Guidelines February 2010 Appendix A. Acknowledgments The authors would like to thank the many people who have engaged in discussions around this topic over the years. Some of the material in this document comes originally from Fred Baker's presentation in a workshop in Shanghai [baker.shanghai]. In addition, the authors would like to thank Mark Townsley with whom the Jari Arkko wrote an earlier document [I-D.arkko-townsley-coexistence]. The authors would also like thank Dave Thaler, Alain Durand, Randy Bush, and Dan Wing who have always provided valuable guidance in this field. Finally, the authors would like to thank Cameron Byrne, Suresh Krishnan, Fredrik Garneij, and Mohamed Boucadair who have commented on early versions of this draft. Authors' Addresses Jari Arkko Ericsson Jorvas 02420 Finland Email: jari.arkko@piuha.net Fred Baker Cisco Systems Santa Barbara, California 93117 USA Email: fred@cisco.com Arkko & Baker Expires August 29, 2010 [Page 15]